Specifications:

  • Brand New Steering and Suspension Kit
  • Comes as a 12 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Tie Rod Adjusting Sleeves
  • Kit Includes: (2) Front Upper Control Arms with Ball Joints
  • Kit Includes: (1) Pitman Arm
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Lower Control Arms with Ball Joints
  • Kit Includes: (1) Idler Arm
  • Kit Includes: (2) Front Inner Tie Rods
  • Quantity: 12 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:54)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:11)
    • Turn the brake rotor by hand or turn the steering wheel to turn the rotor
    • Remove the cotter pin from the tie rod nut using pliers
    • Remove the 19mm bolt from the tie rod end
    • Loosen the 1/2 inch nut and bolt from the tie rod adjusting sleeve
    • Attach the tie rod press tool to the steering knuckle
    • Use the tie rod press tool and a wrench to separate the tie rod end from the steering knuckle
    • Apply penetrating oil to the tie rod adjusting sleeve
    • Measure the distance from the end of the adjusting sleeve to the end of the tie rod
    • Note this measurement
    • Loosen the tie rod from the adjusting sleeve with an adjustable wrench
    • Pull out the tie rod
  3. step : Installing the New Outer Tie Rod (4:08)
    • Thread the new tie rod into the adjusting sleeve
    • Measure the distance from the end of the adjusting sleeve to the end of the tie rod
    • This measurement should match the one noted in Step 2
    • Insert the tie rod into the steering knuckle
    • Start the 19mm nut onto the tie rod
    • Tighten the 19mm nut to between 40 - 45 foot-pounds of torque
    • Turn the nut further to line up the space for the cotter pin
    • Put the cotter pin into place
    • Bend the cotter pin with pliers
    • Tighten the 1/2 inch nut and bolt to 20 - 21 foot-pounds
  4. step : Reattaching the Wheel (5:36)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 100 - 110 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Have the vehicle professionally aligned

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Adjustable Wrench

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 19mm Socket

  • Sockets - SAE

  • 1/2 Inch Socket

  • Specialty Tools

  • Tie Rod Puller

  • Wrenches - SAE

  • 1/2 Inch Wrench

4.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
1
0
0
0
Steering and suspension for a 1999 Lincoln town car
First of all I appreciate your services because I had never order anything off of a website and it was safe and the parts fix perfect so I would tell all of my friends and they will tell all of their friends. I will be ordering my next order from 1aauto. Love your service
March 4, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1995-2002 Ford Crown Victoria 12 Piece Set Steering & Suspension Kit
  • 1996-2002 Lincoln Town Car 12 Piece Set Steering & Suspension Kit
  • 1995-2002 Mercury Grand Marquis 12 Piece Set Steering & Suspension Kit

This part replaces:

  • Dorman 520-207
  • Dorman 520-208
  • Dorman 521-565
  • Dorman 521-566
  • Hollander 512-01333R
  • Hollander 512-01333L
  • Hollander 511-00117L
  • Hollander 511-00118R
  • OE # 2W7Z3A130A, F5AZ3A130A
  • OE # F3AZ3A131A, 2W7Z3A131AA
  • OE # F8AZ3590AA
  • OE # XW1Z 3078-BA
  • OE # XW1Z 3079-BA
  • OE # F6AZ3085BA
  • OE # F7AZ3084BA
  • Moog ES3311S
  • Moog K8283
  • Moog K8688
  • Moog ES2057RL
  • Moog ES3494
  • Moog K80393
  • Moog K80706
  • Moog K80707
  • Moog K80394
Part #: 1ASFK02609

How-to Video:

(06:32 min)