Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   10 Piece Set
  • Kit Includes:
      (2) Front Lower Control Arms
      (2) Front Outer Tie Rods
      (2) Front Sway Bar Links
      (2) Steering Rack & Pinion Bellows
      (2) Front Inner Tie Rods

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

    It is recommended to seek a professional alignment after completing this repair.

  1. step : Removing the Wheel (0:58)
    • Loosen the lug nut covers with a 19mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Front Control Arm (1:20)
    • Loosen the ball joint bolt with a 15mm wrench and a 16mm socket and ratchet
    • Remove the 18mm bolt in the front of the control arm with a socket, ratchet, and pipe for leverage
    • Remove the two 18mm bolts in the large control arm bushing
    • Remove the bolt on the end of the bushing
    • Pry the front of the control arm out with a pry bar
    • Pry out the back bushing with a pry bar
    • Pull the control arm down and out
  3. step : Installing the Front Control Arm (3:29)
    • Insert the ball joint in place
    • Tighten the 16mm bolt in the ball joint by hand
    • Feed the rear part of the control arm and the front part into the frame
    • Hammer the ball joint into place to line it up
    • Tighten the 18mm bolts by hand
    • Tighten the bolt on the end of the bushing by hand
    • Tighten the 18mm bolts on the control arm bushing with a socket and wrench
    • Torque the bolts between 75 and 85 foot-pounds
    • Torque the ball joint bolt to 50 foot-pounds
    • Place a jack underneath the lower ball joint to lift the suspension up until there's just weight off the jack stand
    • Tighten the rear bushing bolt to 55 foot-pounds of torque and the front 18mm bolt to 75 foot-pounds
  4. step : Reattaching the Wheel (5:41)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Ratchet
  • A Piece of Pipe (for leverage)
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 18mm Socket

  • Wrenches - Metric

  • 15mm Wrench
  • 18mm Wrench

4.50/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
1
0
0
0
Steering & Suspension Kit
I ordered the kit and it included all the parts as a set, which was nice. The bellows did not fit my car though. The online videos are great. Over all a good experience. :)
May 9, 2018
1ASFK02600-Steering & Suspension Kit
Had an amazing experience with 1A Auto. Parts were sent as shown online, great experience thus far.
May 23, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2004-2012Chevy Malibu Chevy Malibu 10 Piece Set Steering & Suspension Kit
2005-2010Pontiac G6 Pontiac G6 10 Piece Set Steering & Suspension Kit
2007-2009Saturn Aura Saturn Aura 10 Piece Set Steering & Suspension Kit
Part #: 1ASFK02600


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(06:36 min)