Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as an 8 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:46)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Ball Joint (1:11)
    • Separate the axle from its housing with a pry bar and a hammer
    • Unclip the brake line from its clips
    • Remove the ball joint retaining ring with a hammer and punch
    • Remove two 10mm bolts from the steering knuckle bracket
    • Apply penetrating oil to the control arm nut and bolt
    • Remove the 15mm nut and bolt from the control arm
    • Strike the control arm with a hammer to loosen it
    • Pull the steering knuckle forward
    • Support the wheel knuckle with wire ties
    • Cut off the ball joint boot with a razor
    • Fit a ball joint press to the ball joint
    • Tighten the press to press out the ball joint
    • Remove the ball joint press
    • Tap out the ball joint with a hammer
  3. step : Installing the New Ball Joint (4:22)
    • Push the new ball joint into place
    • Fit the ball joint press onto the ball joint
    • Tighten the ball joint press to press in the ball joint
    • Tap the ball joint in with a hammer
    • Tap the snap ring into place with a hammer and punch
    • If you are replacing the snap ring, put the new ring on with snap ring pliers
    • Push the steering knuckle into place
    • Push the control arm onto the ball joint
    • Tap the control arm onto the ball joint with a hammer
    • Start the 15mm nut and bolt into the control arm
    • Remove the wire ties from the steering knuckle
    • Push the axle into its housing
    • Tighten the 15mm nut to 50 foot-pounds of torque
    • Fasten the grease fitting onto the ball joint with a 10mm wrench
    • Add grease to the ball joint with a grease gun
    • Insert the two 10mm bolts into the steering knuckle bracket
    • Clip the brake line into place
  4. step : Reattaching the Wheel (7:00)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Hammer
  • Razor Blade / Gasket Scraper

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bearing Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket
  • 10mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Grease Gun

  • Wrenches - Metric

  • 15mm Wrench
  • 10mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Steering suspension kit
I like the idea of having a package deal for steering and suspension. Everything fit like it was supposed to. I actually had more work getting the old parts out than putting in the new ones. I would recommend this to my friends and other DIYers. This package deal is the way to go, by not having to buy these parts individually. Thanks 1A Auto.
October 20, 2017
Purchased
4 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(07:51 min)

Tools List:

    General Tools

  • Floor Jack
  • Jack Stands
  • Hammer
  • Razor Blade / Gasket Scraper

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bearing Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket
  • 10mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Grease Gun

  • Wrenches - Metric

  • 15mm Wrench
  • 10mm Wrench



This part replaces:

  • OE # 26100286
  • OE # 26100287
  • OE # 22157319, 19133670, 8191336700
  • OE # 22157320
  • Moog K6663
  • Moog K6664
  • Moog ES3675
  • Moog ES3676
  • Moog K80824
  • Moog K80825

Vehicle Fit

  • 2004-2007 Buick Rainier 8 Piece Set Steering & Suspension Kit
  • 2004-2007 Chevy Trailblazer 8 Piece Set Steering & Suspension Kit
  • 2004-2005 Chevy Trailblazer EXT 8 Piece Set Steering & Suspension Kit
  • 2004-2007 GMC Envoy 8 Piece Set Steering & Suspension Kit
  • 2004 GMC Envoy XL 8 Piece Set Steering & Suspension Kit
  • 2004-2008 Isuzu Ascender 8 Piece Set Steering & Suspension Kit
  • 2004 Olds Bravada 8 Piece Set Steering & Suspension Kit
  • 2005-2009 Saab 9-7X 8 Piece Set Steering & Suspension Kit
Part #: 1ASFK02559

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More