These replacement suspension parts are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Comes as a SET of 8
    • Fits the LH (Driver Side) and RH (Passenger Side) FRONT
    • Kit includes
      • LOWER Ball Joints
      • LOWER Control Arms
      • OUTER Tie Rod Ends
      • Sway Bar End Links
  • Direct replacement
  • Built to strict quality control standards

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:38)
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Pull off the hub cap
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Control Arm (3:26)
    • Remove the two 17mm nuts connecting the ball joint to the control arm
    • Remove the 17mm bolt connecting the ball joint to the control arm
    • Separate the ball joint from the control arm with a pry bar
    • Remove the two 19mm bolts from the front of the control arm
    • Remove the 19mm bolt from the rear of the control arm
    • Remove the control arm with a pry bar
  3. step : Installing the Control Arm (6:25)
    • Put the rear control arm bushing into place
    • Start the 19mm bolt into the control arm bushing
    • Position the control arm, using a pry bar if necessary
    • Insert the longer 19mm bolt into the rear of the control arm bracket
    • Insert the shorter 19mm bolt into the front of the control arm bracket
    • Pry the control arm into place
    • Fasten the 17mm nuts onto the ball joint bracket
    • Insert the 17mm bolt into the ball joint bracket
    • Tighten the two 17mm nuts to 94 foot-pounds of torque
    • Tighten the 17mm bots to 94 foot-pounds
    • Tighten the three 19mm bolts to 152 foot-pounds
  4. step : Reattaching the Wheel (9:12)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts 76 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 21mm Socket
  • 22mm Socket
  • 19mm Socket
  • 17mm Socket
  • 12mm Socket

4.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
0
1
0
0
0
Control arm kit 95 camry
Parts did not have greasable fittings as shown in install videos disappointed that I can't service the parts but fit well and will hope the parts last
March 4, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1992-1996 Lexus ES300 Steering & Suspension Kit 8 Piece Set
  • 1995-1996 Toyota Avalon Steering & Suspension Kit 8 Piece Set
  • 1992-1996 Toyota Camry Steering & Suspension Kit 8 Piece Set

This part replaces:

  • Moog K9499
  • Moog ES3306
  • Moog K90124
  • Moog K620051
  • Moog K620052
  • Dorman 520-405
  • Dorman 520-406
  • Hollander 512-58289L; 512-58385AL
  • Hollander 512-58289R; 512-58385AR
  • OE # 48069-33020; 48069-33031
  • OE # 48820-33010
  • OE # 4333039435
  • OE # 48068-33020; 48068-33031
  • OE # 4504629255
Part #: 1ASFK02187


How-to Video:

(11:29 min)