Specifications:

  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Quantity: 10 Piece Set
  • Kit Includes: (1) Pitman Arm
  • Kit Includes: (2) Front Upper Control Arms with Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (1) Idler Arm
  • Kit Includes: (2) Front Inner Tie Rods

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Stabilizer Links (1:37)
    • Turn the wheels for access to the stabilizer link.
    • Spray the stabilizer with penetrating oil.
    • 9/16â€� socket on the bottom and a 15mm socket on the top. Loosen the stabilizer link.
    • Use a hammer and punch to push the link out.
    • Use vice grips if needed.
  2. step : Replacing the Stabilizer Link (3:08)
    • Push the link up into place.
    • Put the link together in this order:
    • Bushing on the bottom of the control arm.
    • Bushing above the control arm.
    • Washer
    • Shaft
    • Washer
    • Bushing
    • Bushing
    • Washer
    • Nut.
    • Tighten the stabilizer to 15-17ft/lbs.

Tools needed for replacement:

    General Tools

  • Center Punch
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet

  • Sockets - Metric

  • 14mm Socket

  • Sockets - SAE

  • 9/16 Inch Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Good job!
Ordering and tracking my order was simple. The videos were good.
I did one side of the steering and suspension kit at a time and figured out a relatively fool-proof way to fine-tune the alignment: after installing the parts on one side, adjust the tie rod length until the steering wheel is straight when the truck is going straight. Then do the other side.
Another tip: use a small laser level that shoots a vertical line to accurately mark the center of the bolts on the chassis before removing the upper contrast arm.
February 6, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 2 answers
How can I tell if my truck thread is 3.48 or 2.48 ?
doug d on Mar 22, 2016
BEST ANSWER: You can either get under the vehicle and measure it or call the dealer parts department with your VIN# and ask them. Only 2 options for you on this.
what height lift from this lift kit ?
Tommy on Mar 27, 2017
BEST ANSWER: These parts will not lift your vehicle. This is meant to the OEM ride height.

Vehicle Fit

Year Make Model Description
1997-2002Ford Expedition Ford Expedition 4 Wheel Drive with 2.48" Bolt Pattern Idler Arm without Air Suspension Steering & Suspension Kit 10 Piece Set
2004Ford F150 Heritage Truck Ford F150 Heritage Truck 4 Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
1997-2003Ford F150 Truck Ford F150 Truck 4 Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
1997Ford F250 Light Duty Truck Ford F250 Light Duty Truck 4 Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
1998-1999Ford F250 Light Duty Truck Ford F250 Light Duty Truck 4 Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set
1998-2002Lincoln Navigator Lincoln Navigator 4 Wheel Drive with 2.48" Bolt Pattern Idler Arm Steering & Suspension Kit 10 Piece Set

This part replaces:

  • Hollander 511-01023BL
  • Hollander 511-01023BR
  • OE # 1L3Z3350AB
  • OE # 2L3Z3A130AA
  • OE # 2L3Z3A130BA
  • OE # 5L3Z3084C
  • OE # 5L3Z3085C
  • OE # 6L3Z5495A
  • OE # ES3366
  • OE # F65Z3590AA
  • OE # F65Z3A130AA
  • OE # F65Z3A130BA
  • OE # F65Z5495AC
  • OE # F65Z5K483CC
  • OE # F75Z3084BA
  • OE # F75Z3085BA
  • OE # F75Z3350AB
  • OE # F75Z3590AA
  • OE # F85Z3350AA
  • OE # XL3Z3084BA
  • OE # XL3Z3085BA
  • OE # XL3Z3590AA
  • Dorman 520-215
  • Dorman 520-216
  • Moog ES3366T
  • Moog ES3367T
  • Moog ES3369T
  • Moog ES3370T
  • Moog K8722T
  • Moog K8724T
  • OE # 5L3Z3085C, XL3Z3085BA
  • OE # 5L3Z3084C, XL3Z3084BA
  • Moog K8739T
  • Moog K8700
  • Moog K8772
Part #: 1ASFK02161


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(05:08 min)