Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Quantity:   6 Piece Set
  • Kit Includes:
      (2) Front Outer Tie Rods
      (2) Front Lower Control Arms with Ball Joints
      (2) Front Sway Bar Links

Specifications:

  • Comes as a 6 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Removing the Wheel (0:41)
    • Loosen the lug nut covers with a 19mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Sway Bar Link (1:21)
    • Spray the top of the stabilizer link with penetrating oil
    • Place a 14mm wrench to hold the top
    • Place a 14mm socket on the bottom
    • Turn the 14mm socket to loosen the sway bar link
    • Remove the top bushings
    • Remove the sway bar link
    • Remove the center bushings
  3. step : Loosening the Ball Joint (2:05)
    • Replace lug nuts to hold the rotor in place
    • Remove the cotter pin at the top of the ball joint with pliers
    • Jack up underneath the wheel
    • Loosen the castle nut with a 19mm wrench and hammer until it is on by a few threads
    • Hammer the knuckle to loosen the ball joint
    • Use a ball joint splitter with a hammer if the above step does not work
    • Remove the castle nut
    • Lower the jack
  4. step : Removing the Control Arm (4:00)
    • Remove the two 21mm nuts from the control arm
    • Use a T57 or T55 Torx bit and 21mm wrench for the first bolt
    • Use a 19mm socket and ratchet and a 21mm wrench for the second bolt
    • Pull the bolts free
    • Pull and maneuver the control arm down and over
  5. step : Installing the New Control Arm (5:14)
    • Insert the control arm with the ball joint side first
    • Adjust the hole the cotter pin is inserted into so it will fit for the cotter pin
    • Press the ball joint into the knuckle
    • Replace the castle nut
    • Line up the holes on the control arm and push the 21mm bolts through
  6. step : Adjusting the Control Arm (6:18)
    • Jack up underneath the wheel
    • Tighten the castle nut a little further
    • Jack the knuckle until the ball joint is angled to fit the 21mm bolts
    • Hammer the 21mm bolt through
    • Tighten the castle nut the rest of the way
    • Push the cotter pin in place and bend the tabs in opposite directions with pliers
    • Tighten the 21mm bolts
    • Lower the jack
  7. step : Installing the Sway Bar Link (7:34)
    • Place the center bushings of the sway bar link in first
    • Run the sway bar link up through the bushings
    • Replace the top bushing
    • Replace the washer and nut
    • Twist the 14mm nut on
    • Lower the vehicle
    • Place jack stands underneath the control arms
    • Place the weight of the vehicle on the jack stands
    • Tighten up the sway bar link with a 14mm ratchet
  8. step : Reattaching the Wheel (8:23)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 21mm Socket
  • 14mm Socket

  • Specialty Tools

  • Ball Joint Press

  • Torx Drivers & Sockets

  • T55 Torx Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 19mm Wrench
  • 21mm wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1997-2005Buick Century Buick Century 6 Piece Set Steering & Suspension Kit
2005-2007Buick LaCrosse Buick LaCrosse 6 Piece Set Steering & Suspension Kit
2008-2009Buick LaCrosse Buick LaCrosse V6 3.8L without RPO Code FE4 (Special Ride & Handling Suspension) 6 Piece Set Steering & Suspension Kit
2008-2009Buick LaCrosse Buick LaCrosse V6 3.6L without RPO Code FE4 (Special Ride & Handling Suspension) 6 Piece Set Steering & Suspension Kit
1997-2004Buick Regal Buick Regal 6 Piece Set Steering & Suspension Kit
2000-2003Chevy Impala Chevy Impala (excluding Police Package) 6 Piece Set Steering & Suspension Kit
2004-2013Chevy Impala Chevy Impala (excluding Police Package) 6 Piece Set Steering & Suspension Kit for Models with RPO Code FE1 (Soft Ride Suspension)
2000-2007Chevy Monte Carlo Chevy Monte Carlo 6 Piece Set Steering & Suspension Kit
1998-2002Oldsmobile Intrigue Olds Intrigue 6 Piece Set Steering & Suspension Kit
1997-2003Pontiac Grand Prix Pontiac Grand Prix 6 Piece Set Steering & Suspension Kit
2006-2008Pontiac Grand Prix Pontiac Grand Prix 6 Piece Set Steering & Suspension Kit for Models with 34mm Diameter Sway Bar
Part #: 1ASFK02105


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(09:15 min)