Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:00)
    • Loosen the lug nuts.
    • Raise and secure the vehicle
    • Remove the lug nuts and the wheel.
  2. step : Remove the front shield (1:15)
    • Use a 15 mm socket and ratchet.
    • Remove the four bolts.
  3. step : Remove the Idler Arm (1:25)
    • Remove the 24 mm bolt securing the idler arm to the steering linkage
    • Use a joint fork and a hammer to separate the joint.
    • Remove the three other bolts securing the idler arm.
    • Use a Tie Rod Puller to pull apart the idler arm and the idler shaft.
  4. step : Install the new idler arm (4:34)
    • Assemble your new idler arm to your idler shaft, threading on the bushing and nut.
    • Bolt in the idler arm assembly into place, tightening up the three nuts.
    • Bolt in the end of the idler arm assembly to the steering gear.
    • Torque the nuts and bolts to 80 ft lbs.
    • Install the cotter pin.
    • Use a grease gun and fill the grease fitting.
  5. step : Reassembly (7:25)
    • Replace the shield with the four 15mm bolts.
    • Clip the air bag harness back in.
    • Put the wheel back on and lower the car
    • Using a star pattern torque the lug nuts to 120-140 ft lbs

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Large C-Clamp

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Sockets - Metric

  • 15mm Socket
  • 18mm Socket
  • 19mm Socket
  • 22mm Socket
  • 24mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Fork
  • Tie Rod Puller

  • Wrenches - Metric

  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 4 questions Browse 4 questions and 5 answers
Do you have a steering suspension kit for a 1998 silverado?
Chris on Jul 21, 2017
BEST ANSWER: Please view https://www.1aauto.com/1998-chevy-c1500-truck-brake-steering-suspension-kits/y-mo-c/1998-1512-377?partTypeFld=Steering+%26+Suspension+Kit for all of our available kits for the 2WD model Silverado.
Will this fit a 1997 GMC Sierra 4 wd truck?
Debra T on Jan 15, 2018
BEST ANSWER: This part is specific to vehicles with a particular set of options. We will need more information about your vehicle to confirm the fit. Please feel free to call our customer service department for clarification @ 888-844-3393.
How can I tell if I have stamped steel lower control arms?
Tom M on Aug 18, 2017
BEST ANSWER: The easiest way is to call the dealership with your VIN number as they have a more expansive database of what your vehicle was factory equipped with.
Will it fit any 95 chevy k1500?
jake j on Dec 2, 2015
BEST ANSWER: Hello, and thank you for your Inquiry. Yes, the part you���re looking at will be correct for your vehicle. If you have any other questions or would like to place an order with one of our Customer Service Representatives, please feel free to give us a call. Thank you, and have a great day!

Vehicle Fit

  • 1995-1999 Chevy K1500 Truck Steering & Suspension Kit 12 Piece Set for Models with Stamped Steel Lower Control Arms
  • 1995-1999 Chevy K2500 Truck Steering & Suspension Kit 12 Piece Set for Models with Stamped Steel Lower Control Arms 6 Lug Wheels
  • 1995-1999 Chevy Suburban C1500 Steering & Suspension Kit 12 Piece Set for Models with Stamped Steel Lower Control Arms
  • 1995-1999 Chevy Suburban K1500 Steering & Suspension Kit 12 Piece Set for Models with Stamped Steel Lower Control Arms
  • 1995-2000 Chevy Tahoe 4 Wheel Drive V8 5.7L 12 Piece Set Steering & Suspension Kit Models Stamped Steel Lower Control Arms
  • 1995-1999 GMC K1500 Truck Steering & Suspension Kit 12 Piece Set for Models with Stamped Steel Lower Control Arms
  • 1995-1999 GMC K2500 Truck Steering & Suspension Kit 12 Piece Set for Models with Stamped Steel Lower Control Arms 6 Lug Wheels
  • 1995-1999 GMC Suburban C1500 Steering & Suspension Kit 12 Piece Set for Models with Stamped Steel Lower Control Arms
  • 1995-1999 GMC Suburban K1500 Steering & Suspension Kit 12 Piece Set for Models with Stamped Steel Lower Control Arms
  • 1995-2000 GMC Yukon 4 Wheel Drive V8 5.7L 12 Piece Set Steering & Suspension Kit Models Stamped Steel Lower Control Arms

This part replaces:

  • Moog K6477
  • Moog ES2838RL
  • Moog K80631
  • Moog K6292
  • Moog K6447
  • Moog K6335
  • Moog ES2836RL
  • OE # 26051896
Part #: 1ASFK02003

How-to Video:

(08:13 min)