Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as an 11 Piece Kit
    • Fits (LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the Wheel (1:59)
    • Pull off the center cap
    • Loosen the lug nuts
    • Remove the cotter pin and loosen the 35mm hub nut
    • Loosen the seven 13mm 12-point bolts that hold the axle to the front drive
    • Raise and secure the car
    • Remove the wheel
  2. step : Loosen the Torsion Bar (2:54)
    • Spray the torsion bar with spray paint and loosen the torsion bar tension bolt with an 18mm bolt
  3. step : Remove the Tie Rod (3:45)
    • Use a pair of pliers to remove the cotter pin
    • Remove the nut at the end of the tie rod
    • Use a tie rod puller to separate the tie rod
  4. step : Remove the stabilizer links (5:25)
    • Use a 9/16 wrench to secure the bottom and a 14 mm socket to unbolt the stabilizer link
    • Use a hammer and punch to remove the stabilizer link
  5. step : Pull the Axle from the CV Joint (6:52)
    • Unbolt the seven bolts, using a pry bar to keep the hub from rotating
    • Remove the hub nut using a 35 mm socket
    • Give the axle a tap with a hammer and pull the axle out
  6. step : Remove the Ball Joint (9:00)
    • Use a jack and wood plank or two to lift the control arm and relieve tension from the ball joint
    • Unbolt the the ball joint using a breaker bar and 27mm socket
    • Use a ball joint removal tool to pull the ball joint apart
    • With a ball joint press, remove the ball joint completely
    • See Part Two for reassembly

Tools needed for replacement:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller

3.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
0
0
1
0
0
Packaging Issues
The packaging was very bad for the kit. The box was split open and thanks to the UPS driver he kept them all together and went through them to make sure they were all there. Better packaging would be a great plus, at least to withstand the weight of the parts.
October 20, 2017
Purchased
4 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 3 answers
Does this kit come with everything or will I have to get a few parts from a local auto parts store or dealer?
Keegan G on Jan 28, 2017
BEST ANSWER: It comes with everything. You do have to reuse existing bolts, which is typical. I was thoroughly pleased with the purchase. Still driving my 2001 Supercrew.

How-to Video:

(13:53 min)

Tools List:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller



This part replaces:

  • Moog K8694T, K80771
  • Moog K8700
  • Moog ES3366T
  • Moog ES3367T
  • Moog ES3369T
  • Moog ES3370T
  • Moog K8722T
  • Moog K8724T
  • Moog K8772
  • Dorman 520-215
  • Dorman 520-216
  • Hollander 511-01023BL
  • Hollander 511-01023BR
  • OE # 5L3Z3085C, XL3Z3085BA
  • OE # 5L3Z3084C, XL3Z3084BA

Vehicle Fit

  • 1997-2002 Ford Expedition 4 Wheel Drive 11 Piece Set Steering & Suspension Kit
  • 2004 Ford F150 Heritage Truck 4 Wheel Drive 11 Piece Set Steering & Suspension Kit
  • 1997-2003 Ford F150 Truck 4 Wheel Drive 11 Piece Set Steering & Suspension Kit
  • 1997 Ford F250 Light Duty Truck 4 Wheel Drive 11 Piece Set Steering & Suspension Kit for Models with Independent Front Suspension
  • 1998 Ford F250 Light Duty Truck 4 Wheel Drive 11 Piece Set Steering & Suspension Kit
  • 1998-2002 Lincoln Navigator 4 Wheel Drive 11 Piece Set Steering & Suspension Kit
Part #: 1ASFK01808

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More