Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:44)
    • Loosen the lug nut covers with a 22mm socket
    • Pry off the center cap by hand
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:10)
    • Measure the distance from the boot of the inner tie rod to the edge of the outer tie rod
    • Make note of this measurement
    • Loosen the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
    • Remove the 18mm nut from the outer tie rod end
    • Strike the steering knuckle with a hammer to loosen the outer tie rod
    • Pull the outer tie rod out of the steering knuckle
    • Hold the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
    • Twist off the outer tie rod by hand
  3. step : Installing the New Outer Tie Rod (2:08)
    • Attach the grease fitting to the new outer tie rod
    • Tighten the grease fitting with a 7mm socket and ratchet
    • Twist the new outer tie rod onto the inner tie rod
    • Push the outer tie rod into the steering knuckle
    • Fasten the 18mm castle nut onto the outer tie rod
    • Push the cotter pin through the castle nut
    • Twist the cotter pin into place with needle nose pliers
    • Fill the tie rod with grease, using a grease gun
    • Measure the distance from the boot of the inner tie rod to the edge of the outer tie rod
    • This should be the same as the measurement noted in Step 2
    • Tighten the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
  4. step : Reattaching the Wheel (3:33)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 22mm socket

Tools needed for replacement:

    General Tools

  • Hammer

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Specialty Tools

  • Grease Gun

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 3 questions Browse 3 questions and 6 answers
Will this work on a 2005 Chevrolet Tahoe, z71?
Chris S on Apr 9, 2017
BEST ANSWER: Yes, this will fit your 2005 Tahoe. You just need to make sure your pitman arm has 3 grooves and not 4.
Is this a greasable outter?
Colby A on Oct 9, 2017
BEST ANSWER: These will be sealed units.
Hello I'm doing a ball joint and tie rod complete rebuild on both side of my 4x4 2002 chevy silverado 1500 with leveling kit just wanna see if this kit is right for me or I need to upgrade?
Tj B on Apr 10, 2017
BEST ANSWER: These parts will be direct fit replacements, but you want to ensure that the existing Pitman Arm is a 3 groove, instead of a 4 groove.

How-to Video:

(04:28 min)

Tools List:

    General Tools

  • Hammer

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Specialty Tools

  • Grease Gun



This part replaces:

  • Moog ES3493T
  • Moog K6541
  • Moog K6540
  • Moog K6654
  • Moog ES3488
  • Moog K6534
  • OE # 12479051
  • OE # 15295861, 26059210
  • OE # 12475478
  • OE # 19149615
  • OE # 19149617
  • OE # 12475486

Vehicle Fit

  • 2002-2006 Cadillac Escalade with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2003-2006 Cadillac Escalade ESV with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2002-2006 Cadillac Escalade EXT with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2002-2006 Chevy Avalanche 1500 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 1999-2006 Chevy Silverado 1500 4 Wheel Drive with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2007 Chevy Silverado 1500 Classic 4 Wheel Drive with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2000-2006 Chevy Suburban 1500 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 1999-2006 GMC Sierra 1500 4 Wheel Drive with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2007 GMC Sierra 1500 Classic 4 Wheel Drive with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
  • 2000-2006 GMC Yukon XL 1500 with 3 Groove Pitman Arm Steering & Suspension Kit 10 Piece Set
Part #: 1ASFK01793

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More