Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Step 1: Removing the Wheel (0:55)
    • Remove the center cap.
    • Loosen the lug nuts.
    • Raise the vehicle.
    • Remove the lug nuts.
    • Remove the wheel.
  2. step : Step 2: Removing the Front Upper Control Arm (1:10)
    • Jack up the lower control arm to support the suspension.
    • Mark the upper bolts on the control arm with a marker to remember their alignment. Draw a line on the bolt and on to the bracket.
    • Remove the cotter pin from the balljoint.
    • Spray the ball join and upper bolts with penetrating oil.
    • Us a 21mm socket on the balljoint bolt. Hammer it on.
    • Use a breaker bar and pipe for added leverage to loosen the 21mm bolt. Don’t full remove the bolt.
    • Loosen the other two 21mm bolts using a socket and breaker bar.
    • Remove the nut from the balljoint and use a balljoint puller tool to separate the control arm and steering knuckle.
    • Use a 19mm to tighten the balljoint removal tool until it pops.
    • Remove the upper nuts and bolts.
    • Pull the control arm free.
  3. step : Step 3: Installing the New Control Arm (7:18)
    • Use a wire brush where the control arm goes.
    • Put the new control arm in place.
    • Push it down onto the balljoint and start the bolts.
    • Reinsert the upper bolts. Line the marks up.
    • Torque Ball joint nut to 67ft/lbs.
    • Insert new cotter pin and use pliers to bend the end.
    • Put a grease fitting on and pump grease into the ball joint.
    • Raise the vehicle so all the weight is on the suspension.
    • Torque the upper bolts to 100ft/lbs.
  4. step : Step 4: Reinstalling the Wheel (10:57)
    • Put the wheel in place.
    • Replace the lug nuts.
    • Lower the vehicle.
    • Tighten the lug nuts to 100ft/lbs in a star pattern.
    • Replace the center cap.

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Ball Joint Press

3.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
0
0
1
0
0
Installed the kit
All parts fit but delivery was much longer than it should have! Like 3 weeks!
March 8, 2017
Purchased
12 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 3 answers
Does this suspension kit come with bushings, boots and and or dust covers or sold separately?
Nicholas R on Jul 8, 2016
BEST ANSWER: This kit comes with everything you need. You can not go wrong for the price. The upper control arms do have the bushings but you will need to reuse your alignment plates. Other wise all joints have the rubber boots and grease zerks.

How-to Video:

(11:43 min)

Tools List:

    General Tools

  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Ball Joint Press



This part replaces:

  • Moog ES3367
  • Moog K8700
  • Moog K8739T
  • Hollander 511-01022BL
  • Hollander 511-01022BR
  • OE # 1L3Z3350AB
  • OE # 2L3Z3A130AA
  • OE # 2L3Z3A130BA
  • OE # 5L3Z 3084 B
  • OE # 5L3Z 3085 B
  • OE # ES3366
  • OE # F65Z3590AA
  • OE # F65Z3A130AA
  • OE # F65Z3A130BA
  • OE # F75Z3350AB
  • OE # F75Z3590AA
  • OE # F85Z3350AA
  • OE # XL3Z3590AA
  • Dorman 520-217
  • Dorman 520-218
  • OE # F65Z3A130AB
  • OE # F65Z3A130CA
  • OE # 5L3Z3084B
  • OE # 5L3Z3085B
  • OE # F65Z3084AB
  • OE # F65Z3085AB
  • OE # XL3Z3084AA
  • OE # XL3Z3085AA
  • OE # 7L5Z3050A
  • OE # F57Z3050BB
  • OE # F5TZ3078A
  • OE # F5TZ3079A
  • OE # F65Z3078EJ
  • OE # F65Z3078FE
  • OE # F65Z3079EJ
  • OE # F65Z3079FE
  • OE # F67Z3078GA
  • OE # F67Z3079GA
  • OE # F6TZ3078GA
  • OE # F6TZ3079GA
  • OE # F87A3395BA
  • Moog K8694T, K80771
  • Moog ES3366T
  • Moog ES3367T
  • Moog ES3365T
  • Moog K8728T
  • Moog K8726T
  • Moog ES3364

Vehicle Fit

  • 1997-2002 Ford Expedition 2 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with 2.48" Bolt Pattern Idler Arm
  • 2004 Ford F150 Heritage Truck 2 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with 2.48" Bolt Pattern Idler Arm
  • 1997-2003 Ford F150 Truck 2 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with 2.48" Bolt Pattern Idler Arm
  • 2002 Lincoln Blackwood 2 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with 2.48" Bolt Pattern Idler Arm
  • 1998-2002 Lincoln Navigator 2 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with 2.48" Bolt Pattern Idler Arm
Part #: 1ASFK01726

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More