Specifications:

  • Brand New Steering & Suspension Kit
    • Comes as a Set of 10
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Clean up the top of the upper control arm (1:00)
  2. step : Install the ball joint (1:07)
    • Line up the boot on the ball joint and put the ball joint in place and put the nut on it.
    • Bolt the ball joint in with the four nuts and bolts.
    • Torque them to 25 ft lbs
  3. step : Install the tie rod. (2:18)
    • Put the tie rod in place
    • Bolt it in at 55 ft lbs.
    • Put in the cotter pin, hammer it through and bend it with a pair of pliers.
    • Fill the tie rod end with grease.
  4. step : Install the hub (3:35)
    • Put the O ring into the hub.
    • Mount the hub and thread the ABS harness into place.
    • Bolt the hub into place and make sure the shield is in the correct position.
    • Use a star like pattern when bolting in the hub and torque the bolts to 65 ft lbs.
    • Clip and bolt the ABS harness in and connect it.
  5. step : Install the brakes (6:05)
    • Mount the rotor and caliper
    • Bolt the caliper bolts in and torque to 50-60 ft lbs.
    • Use a rubber mallet to help get the caliper on.
  6. step : Install the hub nut and wheel. (7:00)
    • Before putting the wheel on, put the hub nut on and tighten but do not torque.
    • Put the wheel back on and lower the car.
    • Torque the hub nut to 90 ft lbs.
    • Using a star pattern, torque the wheel lug nuts to 75 ft lbs.
    • Put the cap and lug nut covers on.

Tools needed for replacement:

    General Tools

  • Chisel
  • Floor Jack
  • Hammer
  • Jack Stands
  • Rubber Mallet

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 10mm Socket
  • 11mm Socket
  • 12mm Socket
  • 13mm Socket
  • 14mm Socket
  • 15mm Socket
  • 16mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket
  • 20mm Socket
  • 21mm Socket
  • 22mm Socket
  • 24mm Socket
  • 35mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 13mm Wrench
  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1998 Chevy Blazer S10 4 Wheel Drive Offset Tie Rod Steering & Suspension Kit 12 Piece Set
  • 1999-2005 Chevy Blazer S10 4 Wheel Drive Steering & Suspension Kit 12 Piece Set
  • 1998 Chevy S10 Pickup 4 Wheel Drive Offset Tie Rod Steering & Suspension Kit 12 Piece Set
  • 1999-2004 Chevy S10 Pickup 4 Wheel Drive Steering & Suspension Kit 12 Piece Set
  • 1998 GMC Jimmy S-15 4 Wheel Drive Offset Tie Rod Steering & Suspension Kit 12 Piece Set
  • 1999-2001 GMC Jimmy S-15 4 Wheel Drive Steering & Suspension Kit 12 Piece Set
  • 1998 GMC S-15 Sonoma 4 Wheel Drive Offset Tie Rod Steering & Suspension Kit 12 Piece Set
  • 1999-2004 GMC S-15 Sonoma 4 Wheel Drive Steering & Suspension Kit 12 Piece Set
  • 1998 Isuzu Hombre 4 Wheel Drive Offset Tie Rod Steering & Suspension Kit 12 Piece Set
  • 1999-2000 Isuzu Hombre 4 Wheel Drive Steering & Suspension Kit 12 Piece Set
  • 1999-2001 Olds Bravada 4 Wheel Drive Steering & Suspension Kit 12 Piece Set

This part replaces:

  • OE # 12471301
  • OE # 12471300
  • OE # 26054968
  • OE # 17980954
  • OE # 22156908
  • OE # 26029949
  • OE # 26033093
  • OE # 26054932
  • OE # 7830667
  • OE # 7833124
  • OE # 7837636
  • Moog K5335
  • Moog K6251
  • Moog K5320
  • Moog K6600
  • Moog K6255
  • Moog ES3462
  • Moog ES3584
Part #: 1ASFK00733



How-to Video:

(09:04 min)