Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 9 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Lower Ball Joints
  • Quantity: 9 Piece Set
  • Kit Includes: (2) Front Upper Control Arms with Ball Joints
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Inner Tie Rods
  • Kit Includes: (1) Pitman Arm

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Removing the Wheel (0:55)
    • Remove the center cap.
    • Loosen the lug nuts.
    • Raise the vehicle.
    • Remove the lug nuts.
    • Remove the wheel.
  2. step : Removing the Front Upper Control Arm (1:10)
    • Jack up the lower control arm to support the suspension.
    • Mark the upper bolts on the control arm with a marker to remember their alignment. Draw a line on the bolt and on to the bracket.
    • Remove the cotter pin from the balljoint.
    • Spray the ball join and upper bolts with penetrating oil.
    • Us a 21mm socket on the balljoint bolt. Hammer it on.
    • Use a breaker bar and pipe for added leverage to loosen the 21mm bolt. Don’t full remove the bolt.
    • Loosen the other two 21mm bolts using a socket and breaker bar.
    • Remove the nut from the balljoint and use a balljoint puller tool to separate the control arm and steering knuckle.
    • Use a 19mm to tighten the balljoint removal tool until it pops.
    • Remove the upper nuts and bolts.
    • Pull the control arm free.
  3. step : Installing the New Control Arm (7:18)
    • Use a wire brush where the control arm goes.
    • Put the new control arm in place.
    • Push it down onto the balljoint and start the bolts.
    • Reinsert the upper bolts. Line the marks up.
    • Torque Ball joint nut to 67ft/lbs.
    • Insert new cotter pin and use pliers to bend the end.
    • Put a grease fitting on and pump grease into the ball joint.
    • Raise the vehicle so all the weight is on the suspension.
    • Torque the upper bolts to 100ft/lbs.
  4. step : Reinstalling the Wheel (10:57)
    • Put the wheel in place.
    • Replace the lug nuts.
    • Lower the vehicle.
    • Tighten the lug nuts to 100ft/lbs in a star pattern.
    • Replace the center cap.

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Ball Joint Press

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Is their grease fittings on the parts?
Nathan on Oct 15, 2017
BEST ANSWER: These parts are not serviceable, they are pre-packed with grease and ready to install!

Vehicle Fit

Year Make Model Description
1997-2002Ford Expedition Ford Expedition 2 Wheel Drive 9 Piece Set Steering & Suspension Kit
2004Ford F150 Heritage Truck Ford F150 Heritage Truck 2 Wheel Drive 9 Piece Set Steering & Suspension Kit
1997-2003Ford F150 Truck Ford F150 Truck 2 Wheel Drive 9 Piece Set Steering & Suspension Kit
1997-1999Ford F250 Light Duty Truck Ford F250 Light Duty Truck 2 Wheel Drive 9 Piece Set Steering & Suspension Kit
1998-2002Lincoln Navigator Lincoln Navigator 2 Wheel Drive 9 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog K8694T, K80771
  • Moog K8700
  • Moog ES3366T
  • Moog ES3367T
  • Moog ES3365T
  • Moog K8728T
  • Moog K8726T
  • Moog ES3364
  • Dorman 520-218
  • Dorman 520-217
  • Hollander 511-01022BL
  • Hollander 511-01022BR
  • OE # 5L3Z 3085 B
  • OE # 5L3Z 3084 B
Part #: 1ASFK00462


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(11:43 min)