Specifications:
  • Brand New Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the Wheel (1:59)
    • Pull off the center cap
    • Loosen the lug nuts
    • Remove the cotter pin and loosen the 35mm hub nut
    • Loosen the seven 13mm 12-point bolts that hold the axle to the front drive
    • Raise and secure the car
    • Remove the wheel
  2. step : Loosen the Torsion Bar (2:54)
    • Spray the torsion bar with spray paint and loosen the torsion bar tension bolt with an 18mm bolt
  3. step : Remove the Tie Rod (3:45)
    • Use a pair of pliers to remove the cotter pin
    • Remove the nut at the end of the tie rod
    • Use a tie rod puller to separate the tie rod
  4. step : Remove the stabilizer links (5:25)
    • Use a 9/16 wrench to secure the bottom and a 14 mm socket to unbolt the stabilizer link
    • Use a hammer and punch to remove the stabilizer link
  5. step : Pull the Axle from the CV Joint (6:52)
    • Unbolt the seven bolts, using a pry bar to keep the hub from rotating
    • Remove the hub nut using a 35 mm socket
    • Give the axle a tap with a hammer and pull the axle out
  6. step : Remove the Ball Joint (9:00)
    • Use a jack and wood plank or two to lift the control arm and relieve tension from the ball joint
    • Unbolt the the ball joint using a breaker bar and 27mm socket
    • Use a ball joint removal tool to pull the ball joint apart
    • With a ball joint press, remove the ball joint completely
    • See Part Two for reassembly

Tools needed for replacement:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller

4.5 / 5.0
6 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
4
1
1
0
0
Could not be more pleased
Price was awesome, parts arrived in two days, my mechanic said the parts were a PERFECT FIT and EVERYTHING needed to complete the front end job was included. The perfect package if you need parts.
February 6, 2017
Purchased
1 year ago
Easy purchase and quick delivery. Have not installed yet, so I'm not sure about the quality as of yet.
March 11, 2017
Purchased
11 months ago
Great value!
A1 Auto made it easy to get all the parts I need for my truck with one click. Will shop with A1 Auto again, Thanks!!
July 29, 2017
Purchased
7 months ago
Good deal
Every thing fit perfectly. The customer service was excellent! Will defiantly use your company again.no complaints.
March 3, 2017
Purchased
1 year ago
Great deal
IT says lifetime warranty so hope they stand behind the product after its installed. They were a perfect fit! The boots are easy to tear because their isn't a lip to use a cup to press in so it will more than likely tear hints why I hope their lifetime warranty will be up healed. But a really great deal. Will buy from 1a auto again in the future and also super fast delivery!!!
February 1, 2017
Purchased
1 year ago
The front shocks do not fit this vehicle...............................................................................................................................
September 18, 2017
Purchased
5 months ago
Response from 1A Auto
We are sorry to hear that the front shocks did not fit your vehicle. Please call us at 1-888-844-3393 so we may set up a return for refund.
September 18, 2017
Alex PStaff
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
does this kit come with the bolts for the upper control arm to knuckle and is it for coil spring suspension?
daryl h on Oct 3, 2017
BEST ANSWER: I'm not too sure about the bolts for the upper control arm to knuckle however this kit does not fit coil spring suspension, it's meant for the torsion bar suspension.

How-to Video:

(13:53 min)

Tools List:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller



This part replaces:

  • Dorman 520-222
  • Hollander 511-01057AL
  • Hollander 511-01056BR
  • Dorman 520-221
  • Moog K8694T
  • Moog EV317
  • Moog ES3461
  • Moog K7275
  • Moog K8708T
  • Moog K80068
  • OE # 1F703224X
  • OE # 3L5Z3083AA
  • OE # 5L5Z3A130AA
  • OE # F57Z3280AA
  • OE # F57Z3280HB
  • OE # F87Z3A130BA
  • OE # ZZP03224X
  • Moog K8695T
  • Moog K80771

Vehicle Fit

  • 1998-2001 Ford Explorer without Sport Package 10 Piece Set Steering & Suspension Kit for Models with One Piece Design Control Arm
  • 1998-2011 Ford Ranger 2 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with Front Torsion Bar Suspension
  • 1998-2011 Ford Ranger 4 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 1998-2007 Mazda B3000 Truck 4 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 1998-2007 Mazda B3000 Truck 2 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with Front Torsion Bar Suspension
  • 1998-2009 Mazda B4000 Truck 4 Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 1998-2009 Mazda B4000 Truck 2 Wheel Drive 10 Piece Set Steering & Suspension Kit for Models with Front Torsion Bar Suspension
  • 1998-2001 Mercury Mountaineer 10 Piece Set Steering & Suspension Kit for Models with One Piece Design Control Arm
Part #: 1ASFK00001

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More