This replacement wheel hub & tie rod kit is just what you need to get your vehicle in good working order again.

CV Axle Specifications:

  • Comes as a PAIR
    • Includes both the LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part number: 88965657, 88965658
  • Built to strict quality control standards

Tie Rod Specifications:

  • Comes as a PAIR
    • Includes both LH (Driver Side) & RH (Passenger Side) OUTER
  • Come as shown with greasable joints
  • Direct replacements
  • Built to strict quality control standards

Wheel Hub Specifications:

  • Comes as a PAIR
    • Includes both LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 7470017, 7470105, 7470143, 7470567, 7470568, 12429204
  • Wheel studs already included and installed!
  • Have ABS sensors w/stainless steel sensor wire clips
  • Direct replacements
  • Built to strict quality control standards

It is very important when installing to tighten the Hub Nut to 118 foot lbs. Failure to use the correct torque specifications will result in premature failure of the hub.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:42)
    • Loosen the lug nut covers with a 19mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 35mm nut but don't remove it
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Axle (1:50)
    • Remove the hub nut
    • Hit the axle with a hammer
    • Remove the two 21mm bolts at the bottom of the strut with a piece of pipe for leverage
    • Hammer the bolts out
    • Place a drip pan underneath the axle
    • Pry from the back of the axle with a pry bar and hammer
    • Hammer the axle again to loosen it
    • Pull the wheel knuckle forward
    • Pull the axle free and move it to the side
    • Hit the axle out of the wheel knuckle with a hammer
    • Pull the axle up and out
  3. step : Installing the Axle (3:40)
    • Push the axle into place
    • Push the wheel knuckle onto the axle and push the axle into place
    • Place the wheel knuckle into the strut and replace the two 21mm bolts
    • Torque the 21mm strut bolts to 130 foot-pounds
    • Replace the hub nut
  4. step : Reattaching the Wheel (5:16)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the hub nut to 159 foot-pounds
    • Torque the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket
  5. step : Checking the Oil (6:06)
    • Start the car to warm up the transmission
    • Pull out the dipstick
    • Wipe the dipstick clean
    • Recheck the dipstick
    • Replace the amount of oil you need
    • Check the dipstick again

Tools needed for replacement:

    General Tools

  • Drain Pan
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Transmission Fluid

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket
  • 35mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1999-2005 Chevy Venture 6 Piece Set Steering & Suspension Kit for Models with ABS Brakes
  • 1999-2004 Olds Silhouette 6 Piece Set Steering & Suspension Kit for Models with ABS Brakes
  • 1998-2003 Pontiac Grand Prix 6 Piece Set Steering & Suspension Kit for Models with ABS Brakes V6 3.8L (excluding Supercharged Models)
  • 2000-2003 Pontiac Grand Prix 6 Piece Set Steering & Suspension Kit V6 3.1L
  • 1999-2001 Pontiac Montana 6 Piece Set Steering & Suspension Kit for Models with ABS Brakes
  • 2002-2005 Pontiac Montana 6 Piece Set Steering & Suspension Kit with ABS Brakes Front Wheel Drive

This part replaces:

  • A1 Cardone 66-1255
  • A1 Cardone 66-1250
  • Moog ES3453
  • Reference Number 513121
  • Reference Number Axle 150
  • Dorman 951-016
  • Hollander 538-01680B
  • Hollander 447-02511R
  • Hollander 447-02512L
  • OE # 12429204, 7470017
  • OE # 88965658
  • OE # 88965657
Part #: 1AAHK00009



How-to Video:

(06:51 min)