Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

    NOTE: After completing the procedure you will need a professional alignment

  1. step : Removing the Wheel (0:47)
    • Loosen the 22mm caps on the hubcap with the vehicle on the ground
    • Pull the hubcap free
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Upper Control Arm (1:10)
    • Mark the tab on the adjustment piece with a marker to mark the alignment
    • Remove the two 10mm bolts holding the brake line and move the brackets
    • Remove the ball joint nut with an 18mm wrench
    • Hit the wheel knuckle and control arm to break them free
    • Remove the 21mm nuts from the upper control arm bracket
    • Jack up the wheel underneath the wheel knuckle
    • Remove the upper control arm nut
    • Remove the bolts and upper control arm bracket
    • Place a nut back on and use an air hammer to knock the bolt out if it won't budge
    • Move the control arm up and down while pulling out
  3. step : Installing the Upper Control Arm (3:52)
    • Put the upper control arm into place and push the 21mm bolts in to hold it
    • Put the brackets on either side and realign them up
    • Angle the control arm down into the wheel knuckle
    • Replace the 18mm ball joint nut
    • Replace the 21mm nuts from the upper control arm bracket
    • Replace and tighten the two 10mm bolts
    • Put a grease gun into place on the end of the control arm and fill it up
  4. step : Reattaching the Wheel (6:00)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Reattach the hubcap and tighten the caps

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 10mm Socket
  • 21mm Socket
  • 22mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 18mm Wrench
  • 21mm wrench

4.4 / 5.0
8 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
5
1
2
0
0
Good fit, seems to last!
Installed two of these now. No issues on the first in 2 years. Second went right on and has done well so far. Hardest part is getting old parts off.
June 14, 2018
Purchased
1 month ago
Starring and suspension kit
Everything came in a timely manner, completely satisfied with all the parts no issues what so ever.
April 26, 2018
Purchased
2 months ago
Product seems to be good so far no issues came the next day
April 5, 2018
Purchased
3 months ago
2004 Chevy tahoe
Parts came quick. Installed with no problems on tahoe with 240,000. Hopefully they will last another 100,00 ?? thank you A1 auto for the fantastic price !!!
February 17, 2018
Purchased
4 months ago
Awesome product thanks
Thank you so much for the product that you sold me. Need some shocks now can you help me pick the right ones
September 29, 2017
Purchased
9 months ago
The kit is very nice. I haven't installed it yet. The only problem I have with it is that they don't all have grease fittings. The upper balljoints have grease fittings and the rest of the parts do not . That is why I only have it a 3 star. Chances are I will only use the upper ball joints and the stabilizer links unless I decide to drill and put grease fittings in the other ball joints and tie rods.
August 25, 2017
Purchased
10 months ago
Good for the money!
Good product for the money! Everything bolted on with no issues.
The vehicle I put it on is a 2005 Tahoe with 220,XXX miles, so I didn't feel like spending a fortune on it. It would be nice if the kit came with the cam bolts and plates that set the caster and camber. At the very least, these should be suggested as something a person might need, especially in the rusty states.
I wish the fittings were all grease-able, but again, for the money, and where I was putting them, I am satisfied.
August 4, 2017
Purchased
11 months ago
AWESOME-AWESOME-AWESOME
Ya'll must be 40+ years of age. It's nice to know there are still some of us out there that really want to help one another out by providing perfect parts, especially in a kit, and show us how to do it ( Great Videos ). I'm sure it saved me thousands. I don't mine paying for a shop to work on my vehicle, if you can find in honest one, and forget about taking it to a stealership. Thanks for looking out for the guy that likes working on his own vehicles.
I will definitely be getting my parts from ya'll.
P.S. You might want to think about doing kits for old tractors, Kubota, Cat 416, etc. Thanks TEXAS DAN
March 18, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 8 questions Browse 8 questions and 21 answers
How long does it take to get to my house in Michigan?
J D M on Aug 14, 2016
BEST ANSWER: Please keep in mind, it depends on your location and which warehouse ships.
I have a 2001 suburban 1500 LT 4x4. Does every piece of this kit go to my SUV? Thanks!
Ryan P on Jun 11, 2017
BEST ANSWER: Yes, these are meant to fit your Suburban.
Does this fit a 6 lug chevy 4x4?
Jeremy R on Feb 16, 2017
BEST ANSWER: It fits my 2001 4x4 GMC Serra, it has6 lug wheels too.
Very satisfied with fit and operation at a terrific price!
Is there a kit that comes with polyeurathane bushings?
Aaron K on Mar 17, 2018
BEST ANSWER: We only carry kits with rubber bushings, unfortunately.
How do u install lower ball joints ?
Mark da shark on Feb 10, 2017
BEST ANSWER: The lower ball joints must be pressed into the lower control arm with use of a ball joint press. You may rent a kit at any local auto part store, and upon removal of the c-clip the process should be fairly easy to perform.
The upper ball joint started spinning with the stud, whiled tighting the castle nut. What's the problem? Is it the upper ball joint ? Factory promble?
Juan A on Mar 31, 2018
BEST ANSWER: Does the top of the ball joint stud have a set screw hole? If so you will have to hold down the stud using this hole with an allen wrench while using an open wrench on the castle nut.
Will this fit an 05 silverado 4wd with a 6 inch lift?
donni.17 on Nov 14, 2017
BEST ANSWER: Thank you for your question! All of our parts are made to factory spec, so if you have a 6" lift these will not work for you. We do not carry parts to accommodate that kind of lift.
Will they fit a 2006 GMC Sierra 1500 z71?
Joshua Hewett H on Oct 29, 2017
BEST ANSWER: This kit will fit as long as it is a 4x4!

Vehicle Fit

  • 2002-2006 Cadillac Escalade 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 2003-2006 Cadillac Escalade ESV 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 2002-2006 Cadillac Escalade EXT 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 2002-2006 Chevy Avalanche 1500 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 1999-2006 Chevy Silverado 1500 4 Wheel Drive 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 2007 Chevy Silverado 1500 Classic 4 Wheel Drive 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 2000-2006 Chevy Suburban 1500 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 2000 Chevy Tahoe 10 Piece Set Steering & Suspension Kit (excluding Z71 Models) TRQ PSA87843
  • 2001-2006 Chevy Tahoe 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 1999-2006 GMC Sierra 1500 4 Wheel Drive 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 2007 GMC Sierra 1500 Classic 4 Wheel Drive 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 2000 GMC Yukon 10 Piece Set Steering & Suspension Kit (excluding Denali Models) TRQ PSA87843
  • 2001-2006 GMC Yukon 10 Piece Set Steering & Suspension Kit TRQ PSA87843
  • 2000-2006 GMC Yukon XL 1500 10 Piece Set Steering & Suspension Kit TRQ PSA87843

This part replaces:

  • Dorman 520-116
  • OE # 15295861, 26059210
  • OE # 12475478
  • OE # 15864153, 12475485, 15047200
  • OE # 19149617
  • Moog K80942
  • Moog ES3493T
  • Moog K6541
  • Moog K80631
  • Moog ES3488
  • Hollander 511-01044
  • TRQ PSA87843
Part #: 1ASFK01976

TRQ
Brand #: PSA87843

How-to Video:

(07:07 min)