Starter - 1AEST00393

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit


  • Brand New Starter
  • No core charge
  • Direct replacement
  • Built to strict quality control standards

Our electrical and electronic parts are subject to strict quality control testing. Please ensure proper diagnosis of this item before purchasing as the item cannot be returned once installed or plugged in.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm -

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Disconnecting the Battery (0:25)
    • Disconnect the negative terminal with a 10mm wrench
    • Set the terminal aside
  2. step : Removing the Splash Guard (1:00)
    • Jack up and secure the vehicle on jack stands
    • Pry out the push clips from the wheel well liner with a trim tool
    • Pry out the push clips on the splash shield with a trim tool
    • Remove the 10mm bolt from the splash shield
    • Remove the splash shield
  3. step : Removing the Starter (3:11)
    • Remove the 12mm bolts from the bracket
    • Remove the bracket
    • Remove the bottom 17mm mounting bolt from the starter
    • Pry up the wiring case mounted to the transmission
    • Remove the rear mounting bolt with a 14mm socket and ratchet
    • If the starter won't release, spray rust penetrant where the starter meets the transmission
    • Tap the housing with a brass pole and hammer to prevent it from cracking
    • Once separated, pull the starter out
    • Disconnect the solenoid wiring harness
    • Disconnect the rubber boot from the positive wire
    • Remove the starter down
    • Remove the 12mm bolt from the positive wire
    • Remove the starter
  4. step : Installing the Starter (13:16)
    • Connect the positive wire to the starter
    • Tighten the 12mm bolt to the starter
    • Replace the rubber boot to the starter
    • Connect the solenoid wiring harness
    • Insert the starter into place
    • Insert the front 17mm bolt and center the starter
    • Tighten the 17mm mounting bolt
    • Tighten the rear mounting bolt with a 14mm socket and ratchet
    • Clip the wire case to the starter
    • Insert the bracket
    • Tighten the 12mm bolts to the bracket
  5. step : Installing the Splash Guard (21:14)
    • Insert the splash guard into place
    • Tighten the 10mm bolts to the splash guard
    • Tighten the push clips to the splash guard
    • Tighten the push clips to the wheel well liner
  6. step : Connect the Battery (22;53)
    • Tighten the negative battery cable with a 10mm wrench

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Center Punch
  • Floor Jack

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 14mm Socket

  • Wrenches - Metric

  • 10mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Will this starter fit my 2003 cr-v ?
Javier M August 17, 2016
no 2007-11 YM only
Brian F August 17, 2016
Is the replacement procedure the same for a Honda Accord?
Matt R October 29, 2018
Yes, very easy to install.
W.L. C October 29, 2018
The replacement should be very similar.
Emma F October 29, 2018
Year Make Model Description
2006-2014Acura TSX Acura TSX Starter L4 2.4L
2006-2012Honda Accord Honda Accord Starter L4 2.4L
2007-2011Honda CR-V Honda CR-V Starter
2006-2011Honda Civic Honda Civic Starter L4 2.0L
2007-2011Honda Element Honda Element Starter
Part #: 1AEST00393

Out of Stock

How-to Video:

(24:10 min)