Replaces
Replaces Chevrolet GMC Cadillac Front & Rear 5 Piece Air Suspension Kit Arnott ARSFK00016
$1,069.95
Replaces Chevrolet GMC Cadillac Rear 3 Piece Air Suspension Kit Arnott ARSFK00015
$844.95
Replaces Chevrolet GMC Cadillac Front 13 Piece Steering & Suspension Kit MOOG MGSFK00141
$704.95
Replaces Chevrolet GMC Cadillac Front Steering, Suspension, & Brake Kit TRQ PSA64825
$634.95
Replaces Chevrolet GMC Cadillac Front & Rear 5 Piece Air Suspension Kit TRQ PAA80074
$624.95
Replaces 2003-06 Cadillac Escalade Escalade ESV EXT Wheel Center Cap 4 Piece Set General Motors OEM GMWHK00033
$541.95
Replaces Chevrolet GMC Cadillac Ceramic 22 Piece Steering, Suspension, & Brake Kit 12oz TRQ PSA72850
$519.95
Replaces Chevrolet GMC Cadillac 5 Piece Air Suspension Kit TRQ PAA80152
$514.95
Replaces Chevrolet GMC Cadillac Front 17 Piece Steering, Suspension, & Drivetrain Kit TRQ PSA69967
$514.95
Replaces Chevrolet GMC Cadillac Rear 2 Piece Electronic Air Shock Conversion Kit Arnott ARASP00032
$509.95
Part Details
Monroe load adjusting shock absorbers adjust rapidly to changing road and weight conditions, delivering enhanced control with uncompromised ride comfort.
* Capacity is limited by vehicle suspension, tires and transmission. See vehicle owner's manual for details.
Item Condition:
New
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Now, I'm going to take a 22 millimeter socket. Take these lug nuts off. I'm going to take this wheel off. Now, I need to support the rear axle, and I'm just going to use a screw jack. Just take some of the load off of the shock. That should be good right there. Now, I'm going to use a 21-millimeter wrench, and hold the bolt on the lower shock. And then use a 21-millimeter socket, loosen the nut up, and take that nut off. And take that nut off. Then I'll take a punch and a hammer, and just punch the bolt out.
If you have to adjust the tension on the screw jack, pull that out. Make sure that's loose. Now, I want to get this top bolt out and the nut, and I'm going to use a 21-millimeter socket, an extension, and from the backside, I'm going to hold the bolt. And on this side, use a 21-millimeter socket. Take th\ nut off. Slide the bolt out, and grab it from the inside. And you should be able to slide the shock out. If you have to, you can use a pry bar. Just pry this out, and there we go. Slide the shock in position, and get the bolts in from the backside. And just slide the nut on.
Before I tighten the upper bolt, install the lower bolt. You have to adjust the screw jack and get that nut started. Now, I'm going to torque this to 70-foot pounds. And torque this one to 70 as well. Now, I can lower the screw jack and set it aside. We'll take the wheel. Put the wheel back on. Put the lug nuts back on. I'm going to tighten these lug nuts to 140-foot pounds in a cross pattern or star pattern so that it tightens the wheel down evenly. All right, and I'll just go around again. Double-check. Good.
