Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Direct Fit Replacement
Premium Aluminum Core
100% Leak Tested
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Packaging:
Radiators may incur bent cooling fins or small imperfections during shipping or manufacturing. A few bent fins or small dents and scratches do not affect the fit or the function of the part. Neither our 60 Day satisfaction guarantee, nor the manufacturer's warranty, cover these types of insignificant damages.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
We'll go inside the vehicle and open up the hood. To remove this plastic shield that's on the front of the engine compartment there are 10 clips: One, two, three, four, five, six, seven, eight, nine, ten. Take a small, flat bladed screwdriver or trim clip tool. Pop them up to loosen them. We'll need to go in like this. Pull them out. If the middle comes out, it's okay. And then this rubber seal is clipped in here. Just kind of pop it out. With a small flat bladed screwdriver, just pop it out. This trim clip tool, these may break when you're taking them out. You might want to have some new ones on hand. If the middle comes out, it just pushes right back in there. Just repeat that for all the clips. These ones are a little trickier because they're deep inside here. Trying to get this in here to pry them up. Just go along and do the same for all of them. This should just lift right off now. And then we'll put it outside.
There's six T20 Torx bolts, or Torx screws on the top of the radio support that hold the bumper on. We're going to remove those. The top of the bumper is loose. We're going to lift the vehicle up to about waist high. You can take the bumper off of the car on the ground, but this will make it easier for us and easier to show what we're doing. Use a seven millimeter socket, an extension, and a ratchet. There're two seven millimeter bolts here. We're going to remove them. They're holding the bumper to the fender. Just going to tilt the wheel in. We need to do that. You're going to repeat this for both sides of the car.
There are two T20 Torx screws that are holding the fender liner to the bumper. You got all the bolts loose, we kind of tug on the bumper. You see it's starting to come loose. Just repeat this for the other side. For both sides remove the two T20 Torx on the bottom of the fender liner where it connects to the bumper. There's 10 millimeter bolts on each side, and this little bracket's holding the front bumper on. Remove both of those. This bracket's already broken, but you would take this bolt out. Same for the other side. Bumper clips in the brackets, so I'm just going to pull on it. Pull it out of the clips. Sometimes you have to give a good tug. Just go along all the way right along the edge. I'm going to do the other side now the same way. I'm going to support the bumper like that. Pull away from the vehicle.
There are fog lights, or front marker lights. I'm going to unplug those. Do the same for both sides. I'll put our bumper aside.
I'll reinstall the bumper. Don't forget to reconnect the turn signal lamps. Both sides, just snap them into the connector. It'll click when it's in. Put the bumper back into place. Push it up into the bracket. Lift it up and in. Get both sides set. Just clip it into place.
Reinstall the bolts, screws, and clips. Your bracket isn't broken here, this one's broken, but you reinstall the 10 millimeter bolts. It holds the bottom of the bumper on. You do the same for the other side. Reinstall the two Torx screws. You do the same for the other side. Reinstall the two seven millimeter bolts or screws. One had a wider head, one had a smaller head. The smaller head one was towards the inside.
Reinstall the six Torx screws, one on the top of the bumper. Install the upper cover in the inch compartment. Just slide it under that ground point. It's going to go over these rubber mounts here, both sides. Let's go under this weather strips. Same thing for both sides. Reinstall all the push clips. It's easier to push the clips in if you pull out the center part. This is the last one. And that is complete. Close your hood.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Tools used
Tools used
Now, there's no drain on the radiator. So, what we're gonna have to do is take the lower radiator hose off and there's a hose clamp right there, gonna use a hose clamp remover tool. This is a cable type tool. Just remove the hose clamp and grab the lower radiator hose and just slide it back. You might have to twist it back and forth a little bit. Could always use pliers for the hose clamp, and then you're gonna wanna have a drain bucket underneath to catch the coolant. And there's no coolant in this system right now but normally you'd have a lot of coolant draining down. Take my hose clamp pliers off. Now we'll take this cover off, there is pushpins throughout the cover. The ones over here you can use a 90 degree pick. For this one, we'll just use a trim tool to try to get underneath here. Slide that up, take those out. Now take this cover and slide it up.
I'm gonna use a T20 and take these screws out, there's six of them. I did remove the front wheels, although you don't have to, you could always turn the wheel to one side or the other. I need to take these screws out. You can use a T20 socket, take those out. And there's two screws underneath here, take those out with the same T20. On our vehicle, there's two 10-millimeter bolts right here and one on the other side and the bracket behind the bolt is actually broken. So, we don't have to take these out. On your vehicle, you're gonna wanna take those out. You can slide this back just to get it out of the way. Then we need to move this panel. You can take a trim tool, just carefully get underneath here. May be a little more difficult than than this. You can just pry up. And sometimes these plastic clips break, but that's okay. Just keep that out of the way. And there's a fog light right here. Just disconnect that. Some vehicles don't have the fog light. Just push down on the lock and disconnect the connector. You can use a 7-millimeter socket, take this bolt out just like that. All right, then just grab this part of the bumper and just slide it out. It is clipped in. You'll do the same on the other side. Now when you take those off the bumper is gonna be loose, so just be careful. Grab the front and just slide it out.
I'm gonna remove this bracket, there's two 10-millimeter bolts on the bottom, gonna use a ratchet wrench to get those off. And then on top, there's two bolts on this side, two on the other, use a 10-millimeter socket. To make it easier to move some stuff around, I'm gonna take these brackets off. Use a 10-millimeter socket, there's one on this side and one on the passenger side. And just slide it up. We'll just take this piece off right here. Just slide it up. And you can separate the condenser from the radiator. There's two little tabs right here. Just push that. And then on the other side, same thing, two little tabs and just slide that out of the way. These panels have to come off. You can use a trim tool. There's a little push clip here and there should be one underneath here as well. And then on the radiator there is these push retainers, sometimes these can be tricky to get off, you can use a 90 degree pick and a trim tool. Just try to pry the fingers out a little bit. You can bend them a little bit and then try to bend them back when you go to put it back on. Just try not to break it if you're gonna reuse it. So just take those off, there's one there, there is one down here, and there should be one...and there's one down there as well. And there's one more trim piece right here. This piece is actually broken, but just use a trim tool. Take this pushpin out, it's good. Just try to slide it out of the way and then you can do the same on the other side. Slide that out.
On this side, I'm not gonna take this panel off completely, I just need to disconnect it from the radiator and move it back. Because I don't wanna take the condenser lines off, we're not gonna recover the refrigerant, we don't have a machine to do that. We're just gonna have to move this out of the way. So, make sure you don't take that nut off. Now, I can just grab the condenser and just pull it up a little bit. Just have it out of the way, should be good, it'll sit right there. You can take the cap off. Now, you wanna make sure before you drain the coolant or even take the cap off that the engine is cool. You don't want it to be hot, and then take this hose off that goes to the reservoir and just slide it out of the way. Now, I'm gonna take this hose clamp off, use some post clamp pliers or some regular pliers and just slide this outta the way. Now you can take the hose off. If you have to, you can use a 90 degree pick to try to loosen up the hose and slide it off, just like that. You're gonna disconnect the hood latch, there is a wiring harness that goes right here. Just take a trim tool and disconnect the wiring harness from the bracket and disconnect the connector. Slide that out. Before I take this off, I do wanna mark this just so I put it back on the way it came off right there and right here. And I plan on taking this bracket off as well. So, I'm gonna mark this while I'm here. Just do the same. And I'll use a 10-millimeter socket, take these two nuts off and then there's one on this side. And take that off, just slide it out of the way.
Underneath, you're gonna take these two nuts off, use a 13-millimeter socket. Now, I'm gonna take these two bolts out, use a 13-millimeter socket and just grab the bracket and slide it out. Disconnect this electrical connector right here, just push down on the lock tab and slide it out. Now we're gonna disconnect the transmission cooler lines. Just slide this hose out of this bracket right down there and there's a little cover here. Slide this cover off, you can use a pick tool. Slide that out of the way and then there's a clip in there. What we have to do is slide the clip out, can use a pick tool, they do make special tools to take these out. Once you slide it out, can use the pick and just slide this off, you just pull it out all the way. And make sure you have a drain bucket underneath, you might lose some transmission fluid. And just slide this hose off, throw it aside, and we'll do the same with the other hose.
Now, underneath I'm gonna use a trim tool and just take this piece off. It goes around this bracket right here and that's holding me up. Just take any of those clips off. Now just grab the radiator and fan assembly and just slide it up. Might have to wiggle it back and forth a little bit. Just be careful of the condenser, you don't wanna break it. There we go, and there it is. Gonna remove this screw, use a T20, pull that out. Take this screw out, use a T20. And there's two bolts on the side, use a 10-millimeter socket, take those out. Now we can grab the fans, just slide it up a little bit. And just slide it out [inaudible 00:09:20], and you're good. Now, just take this bracket off, you can use a trim tool, just try to slide that out. I'm gonna transfer that over to the new one. And there you go. Now this piece is gonna have to get transferred over to the new one. Just take a trim tool or a screwdriver and just slide that off. Just take this, transfer it over to the new one. Just like that. Looks good. Take these clips, these J-nuts and slide that in position there and same on the other side. Now take the fan shroud, slide it in position over here and over here and make sure it lines up. There we go.
And take the bolts, get that one started right there and same on the other side before I tighten these up, and I'll put the screws in. And tighten this one down. Do the same on the top one. And snug these down. That's good. And you can put this bracket back on right there and you can take these caps off.
There's two over here, right there. All right. And we'll take this. Now, you wanna check to make sure these are in. If these are still stuck to the radiator, swap them over, put those in those positions. Right there, one on each side. We can slide radiator down just like it came out. There you go. Then we take the transmission cooler lines, line those up and clip it in so that it locks in place. There we go. And then take that little cover that goes over that piece right there. Before I switch this bracket, I'll put the top one in and lock that in place. And then we can just twist the bracket. That's good. Then we can plug the fan connector in just like that and hook up the upper radiator hose, slide the clamp down. If the clamp is weak or extremely rusted, then you can replace it with a worm clamp. I can release this clamp with either a screwdriver or a trim tool. Just line it up. Snap it like that. Make sure it's good. And slide this bracket down in position. [inaudible 00:12:28] easier to line it up down below first. There we go, just like that. Get these nuts started. Before I tighten those up down below, take these two bolts, get these in position. Now, tighten these up with that lined up. Now I can tighten them up underneath. Now I can line this up and put the nuts back on. I'm just gonna get it close first and adjust it a little bit. And tighten it down. Now we got to plug the connector in, line that up and then push this back into the position where it's supposed to be with the retainers just like that.
All right. Line up the condenser and snap it into place. Now I can take this shield, slide this in position on this side. The other side, I didn't have to take this off completely. And it's back in position. Then you could take these push clips and slide those on. If these push clips aren't sticking right, just take a hammer with it on the ground. Just bend it back a little bit, then you should be able to reuse it. And it's good. All right. Take this piece, just put that back right there. Take these pushpins, put those back. And get this panel lined up. If this is on the other side, just fold this down. Try to get this over, just like that. We can put those pushpins in there. This pushpin goes right here just like that. All right, I can put the lower radiator hose on. At this point, it's a little bit easier to do it with the bumper off. And slide the clamp over. Just get it in position and release the lock. Reservoir hose over and attach that. You can put the radiator cap on. If you wanted to fill the radiator up right now you could fill it, but you're gonna have to fill the reservoir as well. And take these upper radiator brackets, line those up. And put the bolt in and tighten those down. All right. Now we can take this bracket and line this up just like that. And take these bolts, get these all started first and snug those down.
Now, take the bumper cover and just line it up slowly, get it in position. Just be careful not to scratch anything on the side. It would help if you have a helper helping you get this lined up. And just and snap that back in place. Then take a 7-millimeter screw and line it up right here and snug it up. Push this back in, this trim piece. Then take the connector for the fog light and plug it in. Lock it in place. Then take all these screws, get these lined up. Just get them all started first and then you can tighten them down. Now, take the screws from underneath, put these two in. Then if you had that 10-millimeter bolt on both sides, you're gonna wanna put those in as well. And tighten these down. Then from up top, we can put all these screws in and tighten them down.
Now, before you put this cover on, what you wanna do is fill the radiator up with coolant, use the appropriate coolant, check your owner's manual and you could use a funnel or if you don't have one, just top it off and also top off your reservoir. Then you're gonna wanna run the vehicle for about 10 minutes with the heat on. You wanna monitor the temperature gauge while it's running and just make sure it doesn't go into the red. If it does, shut it off, recheck the level and start over, do it again. After the engine is warmed up, shut the vehicle off, let it cool down, readjust the level and you should be good. And take this panel, line it up and then take the pushpins, reinstall the pushpins.
