Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Our aftermarket cooling fan assemblies are some of the highest quality replacements on the market! This Radiator Cooling Fan Assembly is a complete, ready to bolt on, direct replacement part.

Specifications:

  • Dual Radiator Cooling Fan Assembly
  • Includes shroud, motors, & blades
  • 100% Performance factory tested
  • Replaces dealer part number: 25927026
  • Comes with proper plug(s) for trouble free installation
  • Built to strict quality control standards
  • Direct bolt on
  • Fits models with Air Conditioning only

This fan assembly makes a great replacement and has substantial cost savings over a dealer fan assembly.

Our electrical and electronic parts are subject to strict quality control testing. Please ensure proper diagnosis of this item before purchasing as the item cannot be returned once installed or plugged in.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Draining the Coolant (0:41)
    • Make sure the engine is cool
    • Open the hood
    • Have a drain pan ready
    • Loosen the lower radiator hose clamp with slip joint pliers
    • Pull the hose off the engine
    • Direct the fluid into the drain bucket
    • Allow the coolant to drain completely
  2. step : Removing the Hood Shroud (1:55)
    • Pry the plastic clips out of the hood shroud with a flat blade screwdriver
    • Peel the weatherstip ends off the hood shroud
    • Pull the shroud up and off
  3. step : Removing the Front Bumper Cover (3:32)
    • Remove the T20 Torx bolts from the top of the bumper cover
    • Remove the 7mm bolt from each inner fender
    • Remove the two T20 bolts behind each inner fender
    • Remove the T20 bolts from the bottom of the bumper cover
    • Remove the 10mm bolt from the bumper cover
    • With the help of an assistant, pull off the bumper cover
    • Disconnect the parking light wiring harnesses
  4. step : Removing the Hood Latch (6:13)
    • Remove the four 10mm bolts from the support
    • Remove the support
    • Unclip the push clips on the rubber air guide with a trim tool
    • Slide the air guide down and out
    • For the passenger side, push the air guide out of the way but do not remove
    • Remove the 13mm bolts from the hood latch
    • Unclip the electrical connector
    • Pull the hood latch out and disconnect the electrical connector
  5. step : Removing the Radiator (9:28)
    • Loosen the 10mm bolts from the top radiator mounts
    • Loosen the hose clamp from the upper radiator hose
    • Work the radiator hose off of the radiator
    • Remove the second hose from the radiator neck
    • Unclip the radiator from the a/c condenser
    • Evenly pull the radiator up without stressing the lines
    • Have glove fingers and zip-ties ready
    • Pull the rubber cap from the cooling line
    • Pull the clip on the cooling line out with a pick
    • Disconnect the cooling line and place a glove finger on the end and zip-tie it
    • Repeat this process for the second cooling line
    • Disconnect the cooling fan electrical connector
    • Pull the radiator and cooling fans up, separately from the condenser
  6. step : Separating the Radiator from the Cooling Fans (15:48)
    • Pry up the clip securing the fan to the radiator with a flat blade screwdriver
    • Remove the 10mm bolts from the fan shroud
    • Unclip the fan shroud from the radiator and remove it
  7. step : Installing the Cooling Fans to the Radiator (17:06)
    • Clip the cooling fan shroud to the radiator
    • Tighten the 10mm bolts to the fan shroud
    • Press in the clips to secure the fan to the radiator
    • Clip in the securing clip to the radiator
    • Clip in the air guide to the radiator
    • Tighten the radiator cap
    • Press on the rubber plugs to the bottom of the radiator
    • Insert the lower radiator hose to the radiator
    • Tighten the lower radiator hose clamp
  8. step : Installing the Radiator (18:09)
    • Carefully insert the radiator into place
    • Clip the a/c condenser to the radiator
    • Remove the cooling line caps
    • Remove the glove from the cooling lines
    • Connect the cooling line to the radiator
    • Secure the clip to the cooling line
    • Place the rubber onto the cooling line
    • Repeat this process for the second cooling line
    • Connect the upper hoses to the radiator
    • Secure the hose clamps with pliers
    • Tighten the 10mm bolts to the radiator mounts
    • Slide up the air guides into place
    • Clip in the air guides
  9. step : Installing the Hood Latch (23:18)
    • Connect the hood latch harness
    • Clip the harness in
    • Press the hood latch into place
    • Tighten the 13mm bolt to the hood latch
    • Reinstall the bumper support
    • Tighten the four 10mm bolts to the support
  10. step : Installing the Front Bumper Cover and Lower Radiator Hose (25:08)
    • Connect the parking light wiring harnesses
    • With the help of an assistant, lift the bumper cover into place
    • Push in the bumper cover clips
    • Insert the T20 bolts at the top of the bumper cover
    • Insert the T20 bolts at the bottom of the bumper cover
    • Insert the 10mm bolt in the bottom of the bumper cover
    • Insert the two T20 bolts behind each inner fender
    • Install the 7mm bolt into each inner fender
    • Connect the lower radiator hose
    • Tighten the lower radiator hose clamp with pliers
  11. step : Filling the Coolant (27:55)
    • Push the lower radiator hose onto the engine
    • Tighten the hose clamp with slip joint pliers
    • Twist the radiator cap off the radiator
    • Add coolant to the radiator, using a funnel
    • Add coolant to the overflow reservoir, using a funnel
    • Twist on the radiator cap
  12. step : Bleeding the Cooling System (28:36)
    • Start the engine
    • Bring the engine to between 2,000 and 2,500 RPM
    • Bring the engine to operating temperature
    • Check the coolant level
    • Add coolant to the overflow reservoir as necessary
  13. step : Installing the Hood Shroud (29:43)
    • Put the shroud into place
    • Clip the weatherstrip ends onto the shroud
    • Push the clips into the hood shroud

Tools needed for replacement:

    General Tools

  • Funnel
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Anti-Freeze
  • Gloves
  • Paper Towels
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Trim Tool Set

  • Torx Drivers & Sockets

  • T20 Torx Driver

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
How to replace cooling fan on 2008 Saturn Outlook?
Dontae B January 22, 2017
Year Make Model Description
2008-2017Buick Enclave Buick Enclave Radiator Dual Cooling Fan Assembly
2009-2017Chevy Traverse Chevy Traverse Radiator Dual Cooling Fan Assembly
2007-2017GMC Acadia GMC Acadia Radiator Dual Cooling Fan Assembly
2007-2010Saturn Outlook Saturn Outlook Radiator Dual Cooling Fan Assembly
Part #: 1ARFA00416


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(30:31 min)