Specifications:

  • Brand New High Pressure Power Steering Hose
  • Direct replacement
  • Built to strict quality control standards
  • Correct bends and fittings

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Engine Cover (0:20)
    • Remove the three 10mm bolts from the engine cover
    • Remove the cover
  2. step : Removing the Air Intake (0:42)
    • Loosen the hose clamp on the throttle body
    • Slide the air intake off of the throttle body
    • Disconnect the wiring harness
    • Remove the intake tube from the throttle body
    • Disconnect the vacuum hose
    • Remove the air intake and housing
    • Disconnect the wiring harness
  3. step : Removing the Serpentine Belt (1:46)
    • Slide a 1/4" breaker bar or drive into the tensioner
    • Pull the tensioner clockwise
    • Remove the belt from the pulleys
  4. step : Draining the Power Steering Fluid (2:51)
    • Remove the power steering fluid housing cap
    • Remove the fluid from the suction gun
    • Tighten the cap to the power steering fluid housing
  5. step : Disconnecting the Power Steering Fluid Line (3:23)
    • Raise and support the vehicle on jack stands
    • Have a drain pan ready
    • Remove the high pressure line from the steering box by loosening the bolt
    • Remove the line
    • Catch any fluid from the line
    • Place a glove over the end of the line and zip-tie it
  6. step : Removing the Power Steering Fluid Pump (5:02)
    • Remove the 10mm bolts from the bottom of the pump
    • Loosen the hose clamp from the low pressure return line
    • Disconnect the low pressure return line
    • Remove the 10mm bolts from the top of the pump
    • Remove the power steering pump
  7. step : Removing the Power Steering Pump Line (9:13)
    • Loosen the bolt from the line
    • Remove the line
  8. step : Installing the New Power Steering Line (10:29)
    • Press the o-ring onto the line
    • Thread the line into the pump
    • Tighten the bolt to the pump
  9. step : Installing the Power Steering Pump (11:55)
    • Insert the pump into place
    • Tighten the 10mm bolts to the pump
    • Route the line to the power steering box
  10. step : Connecting the Power Steering Lines (14:19)
    • Install the power steering pressure line to the top of the steering box
    • Tighten the bolt to the line
    • Remove the glove from the return line
    • Press the return line to the pump
    • Tighten the hose clamp
  11. step : Reinstalling the Serpentine Belt (16:03)
    • Bring the belt around the A/C pulley
    • Bring it up under the idler
    • Bring it over the tensioner
    • Bring it under the crank pulley
    • Bring it up and over the water pump pulley
    • Bring it around the power steering pulley
    • Pull the tensioner clock wise with a 1/4" breaker bar
    • Bring the belt over the alternator pulley
    • Release the tensioner
  12. step : Reinstalling the Air Intake (17:55)
    • Connect the connector
    • Push the housing into its grommets
    • Connect the connector
    • Attach the rubber hose
    • Insert the air intake onto the throttle body
    • Tighten the hose clamp
    • Press on the intake box
  13. step : Reinstalling the Engine Cover (18:46)
    • Press the cover into place
    • Tighten the 10mm bolts to the cover
  14. step : Refilling the Power Steering Fluid Reservoir (19:02)
    • Start the vehicle
    • Turn the wheel to the left and right repeatedly until the squealing stops
    • Check the level
    • Refill as needed

Tools needed for replacement:

    General Tools

  • Funnel
  • Jack Stands
  • Pick
  • Drain Pan
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Safety Glasses
  • Gloves
  • Power Steering Fluid
  • Wire Ties
  • Cloth Rags

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers
  • Side Cutters

  • Ratchets & Related

  • Socket Extensions
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-2001 Ford Expedition Power Steering Pressure Hose
  • 2002 Ford Expedition Power Steering Pressure Hose (Built Before 3/18/02 Production Date)
  • 2004 Ford F150 Heritage Truck Power Steering Pressure Hose V8 4.6L
  • 2004 Ford F150 Heritage Truck Power Steering Pressure Hose V8 5.4L
  • 1997-2003 Ford F150 Truck Power Steering Pressure Hose V8 4.6L
  • 1997-2003 Ford F150 Truck Power Steering Pressure Hose V8 5.4L
  • 1997-1999 Ford F250 Light Duty Truck Power Steering Pressure Hose
  • 2002 Lincoln Blackwood Power Steering Pressure Hose
  • 1998-2002 Lincoln Navigator Power Steering Pressure Hose

This part replaces:

  • OE # 6L3Z3A719P
  • Gates 353920
Only 3 left in stock
Part #: 1ASPP00158


Order must be placed by 4pm ET

How-to Video:

(19:43 min)