Replaces

Nissan Wheel Bearing & Hub Assembly Pair TRQ BHA85001 - 1ASHS01217

 

Precision Engineered:

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.
100% Factory tested to precise OEM tolerances.

Highest Quality Materials:

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement:

Guaranteed to fit and function correctly for your specific application.

Part Details

  • Quantity: Pair
  • Includes: (1) 32mm Axle Nut Socket

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:55)
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub Nut (1:31)
    • Remove the 10mm ABS sensor hold down bolt
    • Wiggle the ABS sensor out of the hub
    • Bend the cotter pin up straight with pliers
    • Remove the cotter pin
    • Leverage a 16mm wrench against the caliper by placing it on a stub
    • Tighten a lug nut over the wrench
    • Break the 32mm axle nut loose
    • Remove the lug nut and 16mm wrench
    • Stick a punch in the center diver of the CV axle
    • Tap the punch with a hammer to loosen the splines
  3. step : Removing the Hub (3:13)
    • Remove 13mm bolts from the brake caliper
    • Pull the caliper aside and secure it with a bungee cord
    • Remove the rotor
    • Remove the four 17mm bolts on the backside of the spindle securing the hub
    • Pop the axle out as far as possible
    • Hammer out the hub by hitting the edges to free it from the spindle
    • Hit the CV axle out of the hub
  4. step : Installing the Hub (6:23)
    • Install the dust shield and hub into the spindle
    • Hand-tighten a few 17mm bolts to the backside
    • Insert the axle into the hub
    • Tighten the 17mm bolts with a socket and ratchet
    • Reinstall the axle nut by hand
    • Reinstall the brake rotor
    • Lower the caliper onto the rotor
    • Reinstall the 19mm bolts by hand
  5. step : Installing the Axle Nut (7:34)
    • Install a 16mm wrench to the stud
    • Leverage the wrench against the caliper
    • Tighten a lug nut to the stud
    • Tighten another lug nut to the thread closest to the wrench
    • Tighten the 32mm axle nut
    • Insert the cotter pin into place
    • Bend the cotter pin down
    • Tighten the 10mm bolt to the ABS sensor
  6. step : Reattaching the Wheel (8:25)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 32mm Socket
  • 21mm Socket
  • 16mm Socket
  • 17mm Socket
  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2008-2013 Nissan Rogue Front Wheel Bearing & Hub Assembly Pair with (1) 32mm Axle Nut Socket TRQ
  • 2014-2015 Nissan Rogue Select Front Wheel Bearing & Hub Assembly Pair with (1) 32mm Axle Nut Socket TRQ
  • 2007-2012 Nissan Sentra Front Wheel Bearing & Hub Assembly L4 2.5L Pair with (1) 32mm Axle Nut Socket TRQ

This part replaces:

  • TRQ BHA85001
Part #: 1ASHS01217

Out of Stock

TRQ
Brand #: BHA85001

How-to Video:

(09:11 min)