Replaces

Nissan Rogue Strut & Spring Assembly Pair - 1ASSP01049

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Pre-Assembled

Pre-assembled, loaded strut & spring assemblies allow for a quicker, safer install than replacing with just bare struts. 

Trouble-Free Install

Trouble-free install includes the matched parts needed to get the job done. New mounts, bearings, springs and hardware will provide a better ride for your vehicle and save you time from not having to do the job again because a used part failed afterwards.

Matched Parts

When you buy the kit pre-built by us, you can be sure that the parts are matched for optimum performance.  Not all shocks and struts are manufactured the same, so mixing and matching can result in fit issues and potentially decrease the life of the parts.

Saves Time & Money

When you buy one of our kits, you not only save money over buying the parts individually, but you also save time having to search for all of the different parts that are correct for your vehicle (because we did it for you!)

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:58)
    • Loosen the lug nut covers with a 22mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Strut Assembly (1:36)
    • Pry off the flexible brake hose from the clip
    • Remove the rubber retainer for the ABS sensor
    • Place locking jaw pliers on the backside of the sway bar link joint
    • Remove the nut with an 18mm socket and ratchet
    • Remove the sway bar link from the strut
    • Remove the 21mm bottom strut bolts
    • Move the spindle out of the strut
    • Remove the rubber cover on the cowl panel
    • Remove the inside 13mm bolts
    • Loosen the last 13mm down to the end of the threads
    • Support the strut without pushing up
    • Lower the strut down and out
    • Leave the bolt in the socket extension
  3. step : Installing the Strut Assembly (5:15)
    • Set the thread into the nut on the new strut on the bolt
    • Set the strut into place
    • Tighten the 13mm bolt
    • Tighten the inside 13mm bolts
    • Reinstall the steering knuckle into the bottom of the strut
    • Tighten the 21mm bolt to the bottom of the strut
    • Clip locking pliers to the back of the sway bar link
    • Tighten the 18mm nut to the sway bar link
    • Reconnect the ABS harness to the hangers
    • Slide the brake hose into place
    • Reinstall the spring clip and tap it in
  4. step : Reattaching the Wheel (8:02)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 18mm Socket
  • 13mm Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Strut and Spring Assembly Pair
Outstanding product! The fact it is an entire assembly makes installation very easy. No disassembly of the old spring and strut is required. This was an installation I wasn't sure I could do myself until I viewed the terrific video available at 1A Auto.com. The video explains step by step exactly how to remove the old strut and install the new. Kudos to the gentleman in the video; he does a wonderful job.
April 22, 2018
Purchased
3 weeks ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2008-2011 Nissan Rogue Front Strut & Spring Assembly Pair
  • 2012 Nissan Rogue Front Strut & Spring Assembly Pair (Built Before 1/12 Production Date)

This part replaces:

  • Hollander 1ASTS02230
  • Hollander 527-50528L
  • Monroe 172609
  • Monroe 172608
Part #: 1ASSP01049


How-to Video:

(08:48 min)