Nissan Heater Blower Motor with Fan Cage - 1AHCX00341

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit


  • New, not remanufactured or rebuilt
  • Includes blower motor fan cage impeller already installed
  • Direct replacement
  • Built to strict quality control standards
  • 100% tested prior to leaving the factory

Our electrical and electronic parts are subject to strict quality control testing. Please ensure proper diagnosis of this item before purchasing as the item cannot be returned once installed or plugged in.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Lower Dash Trim (0:23)
    • Remove the T20 Torx screw from underneath the hood release latch
    • Pry out the lower dash trim from the steering wheel
    • Loosen the hood release latch cable from the switch
    • Release the latch cable from the bracket
    • Press the tabs on the harness
    • Release the harness from the dash
    • Unclip the harness wiring from the dash with needle nose pliers
  2. step : Removing the Steel Support (3:47)
    • Remove the four 10mm bolts from the steel trim underneath the steering wheel
    • Remove the 10mm nuts from bracket
    • Remove the air duct
    • Pull the bracket/steel support down and out
  3. step : Removing the Brake Pedal and Gas Pedal Assembly (5:44)
    • Pry off the e-clip from the brake pedal assembly with pliers
    • Disconnect the electrical connectors from the brake pedal switches
    • Remove the 13mm bolts from the brake pedal assembly
    • Unclip the harness from the brake pedal assembly with needle nose pliers
    • Unplug the electrical connection to the gas pedal
    • Remove the two 13mm nuts on the backside of throttle
    • Remove the assembly
    • Remove the pin
  4. step : Removing the Blower Motor (9:47)
    • Disconnect the connector
    • Remove the 8mm bolt
    • Turn the blower motor counterclockwise to unlock it
    • Lower the blower motor down and out
  5. step : Installing the Blower Motor (12:33)
    • Insert the blower motor into place
    • Turn the blower motor clockwise to lock it
    • Tighten the 8mm bolt to the blower motor
    • Connect the connector
  6. step : Installing the Brake Pedal and Gas Pedal Assembly (16:39)
    • Insert the assembly into place
    • Tighten the 13mm bolts by hand
    • Tighten the 13mm bolts
    • Insert the pin into place
    • Clip in the e-clip to the brake pedal assembly
    • Clip in the harnesses
    • Connect the gas pedal assembly wiring harness
  7. step : Installing the Steel Support (19:40)
    • Insert the steel support into place
    • Tighten the 10mm bolt to the bracket
    • Clip the air duct into place
    • Insert the reinforcement plate
    • Tighten the four 10mm bolts to the reinforcement plate
  8. step : Installing the Lower Dash Trim (21:19)
    • Connect the hood release cable
    • Connect the harness to the dash
    • Clip the harness in
    • Line the dash up
    • Press the dash into place
    • Tighten the T-20 Torx screw beneath the hood release

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet
  • Swivel

  • Sockets - Metric

  • 13mm Socket
  • 8mm Socket
  • 10mm Socket

  • Torx Drivers & Sockets

  • T20 Torx Driver

5.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Blower motor for rogue
Excellent fit and easy to install with installation video. I think it actually works better than the original defective part. I would definitely recommend this item for a direct fit replacement. Fast shipping too. Thank you so much!
April 8, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Do you sell the blower motor resistor for a 2012 Nissan Sentra?
Breanna T June 21, 2017
Year Make Model Description
2008-2013Nissan Rogue Nissan Rogue Heater Blower Motor with Fan Cage
2014-2015Nissan Rogue Select Nissan Rogue Select Heater Blower Motor with Fan Cage
2007-2012Nissan Sentra Nissan Sentra Heater Blower Motor with Fan Cage
Part #: 1AHCX00341

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(24:22 min)