Replaces

Nissan Frontier Xterra CV Axle Shaft TRQ CSA82313 - 1AACV00051

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Specifications

  • Fits LH (Driver) or RH (Passenger Side) FRONT
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charge
  • Fits all models

 

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

100% New Components

For quality fit, finish, and easy installation.

Heat Treated

For longer-lasting life and consistent performance under different road conditions.

Precision Machined

And made of brand new components, held to tighter tolerances for better consistency than rebuilt parts.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

    It's recommended to seek a professional alignment after completing this installation

  1. step : Removing the Wheel (1:07)
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Remove the Hub Assembly (1:26)
    • Place a long flat blade screwdriver in the brake rotor
    • Remove the six 6mm Allen bolts on the hub assembly
    • Remove the circlip on the axle
    • Slide the outer bearing out with the circlip
    • Remove the two Phillips head screws on the washer
    • Remove the two washers with a flat blade screwdriver
  3. step : Removing the Axle (3:05)
    • Place a flat blade screwdriver against the axle shaft to prevent it from spinning
    • Remove the six 12mm bolts from the axle shaft
    • Remove the cotter pin from the castle nut on the upper part of the steering knuckle with pliers
    • Use a hammer and pick if the pin will not come out
    • Loosen the castle nut with a 22mm wrench
    • Jack underneath the knuckle
    • Remove the castle nut with a 22mm wrench
    • Thread the castle nut on four to five turns with a 22mm wrench
    • Lower the floor jack leaving 1/4 inch between the jack and the lower ball joint
    • Hit the knuckle with a hammer to loosen it from the control arm
    • Raise the knuckle on a jack
    • Remove the castle nut
    • Slowly lower the jack
    • Pull the axle shaft out
  4. step : Installing the New Axle (7:24)
    • Swap over the washer from the old axle shaft to the new one
    • Feed the new axle in to place pushing the outer part of the axle into the hub assembly first
    • Request the help of an assistant
    • Lower the jack
    • Jack up the knuckle and align the spindle into the ball joint
    • Press down on the control arm to keep it aligned in the ball joint
    • Tighten the 22mm castle nut
    • Lower the jack
    • Push a new cotter pin into the castle nut and bend the ears back
    • Insert and tighten the 6mm bolts to the axle shaft
    • Torque the bolts to 40 foot-pounds
  5. step : Reinstalling the Hub Assembly (10:00)
    • Insert the two washers
    • Insert and tighten the two Phillips screws to the washers
    • Push in the outer bearing
    • Insert the circlip into place with circlip wires
    • Push on the hub
    • Insert and tighten the six 6mm Allen bolts
    • Tighten the hub bolts to 10 to 12 foot-pounds
  6. step : Reattaching the Wheel (11:25)
    • Slide the wheel into place
    • Start the 22mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    Allen Wrenches

  • 6mm Allen Wrench

  • General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Circlip Pliers
  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • A Piece of Pipe (for leverage)
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar
  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 22mm Socket

  • Wrenches - Metric

  • 12mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1998-2004Nissan Frontier Nissan Frontier Front CV Axle Shaft Driver or Passenger Side TRQ CSA82313
2000-2004Nissan Xterra Nissan Xterra Front CV Axle Shaft Driver or Passenger Side TRQ CSA82313
Part #: 1AACV00051


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: CSA82313

How-to Video:

(12:09 min)