Replaces

Nissan Front Outer 2 Piece Tie Rod Set DIY Solutions

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A

Part Details

  • Set Quantity:   2 Piece

These outer tie rod ends are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT OUTER
  • Replaces dealer part numbers: 48520-4B000, 48520-50A26, 485204B000, 4852050A26
  • Direct replacements
  • Built to strict quality control standards

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components come pre-greased,  sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Your DIY Solution—Complete Repair in One Purchase

Do you need an assortment of parts to complete a repair? Stop searching for parts individually and complete your repair in a single purchase with a customized kit or set from DIY Solutions.

High-Quality Parts From Trusted Brands

Parts in DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.

Guaranteed Fit

DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Diagnose (0:55)
    • Raise and secure your vehicle.
    • Grab your wheel on both sides and wiggle the wheel.
    • If the spindle and wheel are moving, but not the tie rod, the tie rod needs to be replaced.
  2. step : Remove the wheel (1:41)
    • Remove the lug nuts.
    • If you don’t have air tools, lower the vehicle, loosen the lug nuts and raise and secure the vehicle once again.
    • Remove the lug nuts.
    • Take the wheel off and set it aside, preferably under a jack point on the car for added insurance should your jack stand fail.
  3. step : Remove the tie rod (2:08)
    • Use a measuring tape to measure your tie rod to help you make a rough alignment when you install the new tie rod.
    • Remove the cotter pin in the castle nut.
    • Use a 19 mm wrench, loosen the nut between the inner and outer tie rods.
    • Remove the 18 mm castle nut with a socket and ratchet.
    • Use a hammer to loosen up the outer tie rod.
    • Remove the outer tie rod by unscrewing it from the inner tie rod.
  4. step : install the new outer tie rod (2:57)
    • Install the grease fitting onto the outer tie rod
    • Twist your new outer tie rod in place.
    • Insert the end of the outer tie rod into the spindle.
    • Match the tie rod up to your prior measurements using your measuring tape.
    • Tighten up the castle nut with your 18 mm socket and ratchet and install the cotter pin.
    • Tighten up the 19 mm nut with your wrench.
    • Use a grease gun to fill the grease cap.
  5. step : Replace the wheel (4:13)
    • Put the wheel on and put the lug nuts on and hand tighten them.
    • Lower the vehicle and torque the lug nuts in a star pattern to 100 ft lbs.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Measuring Tape
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 7mm Socket
  • 18mm Socket
  • 21mm Socket
  • 20mm Socket

  • Specialty Tools

  • Grease Gun

  • Wrenches - Metric

  • 19mm Wrench

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Tie rod ends
Easy fit and installation also help to stabilize the steering wheel shaking and alignment.
October 28, 2019
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Do these come with grease fittings?
S T October 16, 2015
No grease fitting.
Sergio A October 16, 2015
how would I measure what MM tie rods I would need? I have a 2002 trailblazer I read 2002 trailblazers take 14MM and 2003 take 16MM. any truth to that?
DAVID F November 24, 2015

Fits the following Makes:

Year Make Model Description
1995-1997Nissan 200SX Nissan 200SX Front Outer 2 Piece Tie Rod Set
1989-1994Nissan 240SX Nissan 240SX Front Outer 2 Piece Tie Rod Set
1996-2001Nissan Altima Nissan Altima Front Outer 2 Piece Tie Rod Set
1987-1990Nissan Pulsar Nissan Pulsar Front Outer 2 Piece Tie Rod Set
1986-1997Nissan Sentra Nissan Sentra Front Outer 2 Piece Tie Rod Set
2000-2006Nissan Sentra Nissan Sentra Front Outer 2 Piece Tie Rod Set
1986-1988Nissan Stanza Nissan Stanza Front Outer 2 Piece Tie Rod Set

Part Interchange

Brand Label Part Number
DIY Solutions SUS00788
DIY Solutions SUS07399
MOOG ES2814RL
MOOG Chassis Products ES2814RL

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

Part 1ASFK00288
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

DIY Solutions
Brand #: SUS00788