Nissan CV Axle Shaft TRQ CSA82123 - 1AACV00167

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit


  • Brand new, not rebuilt CV Axle Shaft
  • Fits RH (Passenger Side) FRONT OUTER
  • Overall Length: 38-1/8"
  • Inboard Splines: 27
  • Outboard Splines: 29

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

100% New Components

For quality fit, finish, and easy installation.

Heat Treated

For longer-lasting life and consistent performance under different road conditions.

Precision Machined

And made of brand new components, held to tighter tolerances for better consistency than rebuilt parts.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm -

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:55)
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Hub Nut (1:31)
    • Bend the cotter pin up straight with pliers
    • Remove the cotter pin
    • Leverage a 16mm wrench against the caliper by placing it on a stub
    • Tighten a lug nut over the wrench
    • Tighten a lug nut next to the wrench to protect the stud
    • Break the 32mm axle nut loose
    • Remove the lug nut and 16mm wrench
    • Stick a punch in the center diver of the CV axle
    • Tap the punch with a hammer to loosen the splines
  3. step : Removing the CV Axle Shaft (2:53)
    • Remove 19mm bolts from the brake caliper
    • Pull the caliper aside and secure it with a bungee cord
    • Remove the rotor
    • Pry the ABS wire out of its bracket
    • Remove both the nuts and bolts from the bottom of the strut plate
    • Remove the two 13mm bolts on the lock plate for the CV axle
    • Remove the lock plate
    • Place a striking bar or long punch on front edge of the bearing on the engine side of the cv axle support bracket and hit it with a hammer to knock it out of its holder
    • Remove the CV Axle
  4. step : Installing the CV Axle Shaft (6:13)
    • Reinstall the CV Axle into the differential
    • Knock the joint in with a rubber mallet
    • Reinstall the lock plate
    • Reinstall the 13mm bolts to the lock plate without overtightening
    • Reinstall the splines of the CV axle into the hub
    • Install the 32mm axle nut by hand a few threads
    • Reinstall the spindle into the strut
    • Insert the bottom strut bolt
    • Insert the top strut bolt
    • Tighten the 21mm strut bolts
    • Reinstall the ABS sensor into the holders
  5. step : Installing the Rotor and Axle Nut (8:17)
    • Reinstall the brake rotor
    • Lower the caliper onto the rotor
    • Reinstall the 19mm bolts by hand
    • Install a 16mm wrench to the stud
    • Leverage the wrench against the caliper
    • Tighten a lug nut to the stud
    • Tighten another lug nut to the thread closest to the wrench
    • Tighten the 32mm axle nut
    • Insert the cotter pin into place
    • Bend the cotter pin down
    • Tighten the 10mm bolt to the ABS sensor
  6. step : Reattaching the Wheel (9:31)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern
  7. step : Refilling the Transmission Fluid (10:10)
    • If you lost transmission fluid, follow this step
    • Use a small flat blade screwdriver to depress the tab on the dipstick
    • Remove the transmission dipstick
    • Insert a transmission fluid funnel into the hose
    • Replace the amount of fluid lost with the appropriate transmission fluid
    • Check the new fluid level with the vehicle running in park and at operating temperature

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Rubber Mallet
  • Center Punch
  • Hammer
  • Drain Pan
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Transmission Fluid
  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 32mm Socket
  • 21mm Socket
  • 19mm Socket
  • 16mm Socket
  • 13mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 21mm wrench
  • 16mm Wrench
  • 15mm Wrench
  • 19mm Wrench

3.00/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
My confidence in 1A has significantly decreased
I ordered a right driveshaft for my 2008 Nissan Altima. I order it through 1A because it was the only driveshaft that I found with a dampener system. The part arrived incomplete and damaged. It was missing the nut, it didnt have a dampener and the threading was damaged. I didnt have the option to return the part as the old driveshaft was already pulled out. I had to purchase a tool to fix the thread and installed the OEM nut. Next time I will consider other vendors before 1A
June 27, 2017
Love this place.
Ive ordered often from 1A and always surprised at how soon my order arrives. Very good customer service also. Love these guys.
June 26, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2007-2011Nissan Altima Nissan Altima (excluding Hybrid Models) Front Outer CV Axle Shaft L4 2.5L CVT Transmission Passenger Side TRQ CSA82123
2012Nissan Altima Nissan Altima Front Outer CV Axle Shaft L4 2.5L CVT Transmission Passenger Side TRQ CSA82123
2013Nissan Altima Nissan Altima Coupe Front Outer CV Axle Shaft L4 2.5L Passenger Side CVT Transmission TRQ CSA82123
2008-2013Nissan Rogue Nissan Rogue Front Wheel Drive Front Outer CV Axle Shaft Passenger Side TRQ CSA82123
2014-2015Nissan Rogue Select Nissan Rogue Select (Japan Built Models (1st VIN Digit J)) Outer Front Wheel Drive CV Axle Shaft Front Passenger Side TRQ CSA82123
2007-2012Nissan Sentra Nissan Sentra Front Outer CV Axle Shaft L4 2.5L CVT Transmission Passenger Side TRQ CSA82123
Part #: 1AACV00167

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Brand #: CSA82123

How-to Video:

(11:04 min)