These Tie Rod Ends are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Comes as a SET of 4
    • Fits both the LH (Driver Side) & RH (Passenger Side) FRONT INNER and OUTER
  • Replaces dealer part numbers: 485200M085, 485217Y000, 485218J000, 485200-M085, 48521-7Y000, 48521-8J000
  • Direct replacements
  • Built to strict quality control standards

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : remove the wheel (0:50)
    • Loosen your lug nuts
    • Raise and secure your vehicle
    • Remove the lug nuts and the wheel
  2. step : Remove the tie rod (1:13)
    • Measure your tie rod to help make a preliminary alignment later.
    • Remove the cotter pin in the castle nut.
    • Remove the 19 mm castle nut.
    • Use a hammer to break the tie rod free and lift it up and out.
    • Unscrew the outer tie rod and remove it.
  3. step : Install the new outer tie rod (2:09)
    • Install the grease fitting.
    • Put the outer tie rod onto the inner tie rod.
    • Place the tie rod end into the knuckle.
    • Replace the 19 mm castle nut.
    • Measure your tie rod and make sure it is the same distance as the old one.
    • Tighten up the middle nut when it is.
    • Put your cotter pin into the castle nut.
  4. step : Put your wheel back on (3:30)
    • Thread the lug nuts.
    • Lower the vehicle
    • Tighten the lug nuts to 100 ft lbs.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket
  • 7mm Socket

5.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
3
0
0
0
0
Nissan Altima tie rods
Just as described ;perfect fit. Recommended seller.
March 3, 2017
Purchased
1 year ago
Awesome
I love 1 A Auto. Their prices are much lower than the competition. I wish they had a store close by.
October 19, 2017
Purchased
7 months ago
Awesome product top quality
I put these in my 240sx s13 and they are awesome for my application work amazingly!
September 13, 2017
Purchased
7 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 3 answers
are the left and right inner tie rods different or same length for maxima 2003?
kevin on May 2, 2016
BEST ANSWER: Yes they are the same length for the inner

Vehicle Fit

  • 2002-2006 Nissan Altima Inner & Outer Tie Rod 4 Piece Set
  • 2003-2008 Nissan Maxima Inner & Outer Tie Rod 4 Piece Set

This part replaces:

  • Moog ES3438
  • Moog EV427
  • OE # 485200M025, 485200M085
  • OE # 485217Y000, 485218J000
Part #: 1ASFK01835

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(04:01 min)