Replaces

Nissan Altima Maxima Steering & Suspension Kit - 1ASFK05156

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : remove the wheel (0:50)
    • Loosen your lug nuts
    • Raise and secure your vehicle
    • Remove the lug nuts and the wheel
  2. step : Remove the tie rod (1:13)
    • Measure your tie rod to help make a preliminary alignment later.
    • Remove the cotter pin in the castle nut.
    • Remove the 19 mm castle nut.
    • Use a hammer to break the tie rod free and lift it up and out.
    • Unscrew the outer tie rod and remove it.
  3. step : Install the new outer tie rod (2:09)
    • Install the grease fitting.
    • Put the outer tie rod onto the inner tie rod.
    • Place the tie rod end into the knuckle.
    • Replace the 19 mm castle nut.
    • Measure your tie rod and make sure it is the same distance as the old one.
    • Tighten up the middle nut when it is.
    • Put your cotter pin into the castle nut.
  4. step : Put your wheel back on (3:30)
    • Thread the lug nuts.
    • Lower the vehicle
    • Tighten the lug nuts to 100 ft lbs.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket
  • 7mm Socket

3.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
0
0
1
0
0
Quality vs price
Quality was decent, compared to local auto parts supplier. More than half my order was lost during shipping due to the packaging, they corrected and sent the missing items.
September 5, 2017
Purchased
9 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2002-2006 Nissan Altima V6 3.5L 10 Piece Set Steering & Suspension Kit
  • 2004-2008 Nissan Maxima 10 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog K620167
  • Moog K620166
  • Moog K90352
  • Moog K90353
  • Dorman 520-511
  • Dorman 520-512
  • Hollander 538-58824
  • Hollander 512-58634L, 512-58823L
  • Hollander 512-58633R, 512-58822R
  • OE # 485200M025, 485200M085
  • OE # 402103Z000, 402022Y010
  • OE # 545017Y00A, 54501-8J000
  • OE # 54500-8J000, 545007Y00A, 00
  • OE # 546688J000
  • OE # 546188J000
  • OE # 485217Y000, 485218J000
  • Moog ES3438
  • Moog EV427
Part #: 1ASFK05156


How-to Video:

(04:01 min)