This Neutral Safety Switch is a new, aftermarket replacement part that has the following specifications:

  • Mounts on transmission
  • Rotating type with (1) plug with 11 pins
    • not correct for models with 8 pins
  • Replaces dealer part number: F5TZ7A247B, F5TZ 7A247 B, XW4Z7F293AA, XW4Z 7F293 AA, F7TZ7A247AA, F7TZ 7A247 AA
  • Direct fit
  • Built to strict quality control standards
  • Fits models with E4OD / 4R100 Automatic Transmissions Only
    • (20 bolt pan)

If your vehicle is having problems starting because of a defective neutral safety switch, then this is the part for you!

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Neutral Safety Switch (0:15)
    • Park the vehicle on level ground
    • Chock the wheels
    • Put the transmission in neutral
    • Clean the neutral safety switch with brake parts cleaner
    • Wipe off the switch with paper towels
    • Disconnect the electrical connector from the switch
    • Counterhold the shifter control arm arm with groove jaw pliers
    • Remove the 15mm nut from the neutral shifter control arm
    • Pry off the arm with a flat blade screwdriver
    • Turn the switch shaft with a 12mm wrench to line up the marks
    • Remove the two 8mm bolts from the switch
    • Pry the switch off the transmission selector shaft with a flat blade screwdriver or pry bar
    • Clean the switch mounting area with a wire brush
    • Clean the switch mounting rea with brake parts cleaner
  2. step : Installing the Neutral Safety Switch (5:31)
    • Line up the switch keyways with the transmission selector shaft keyways
    • Turn the switch by hand to line up the marks
    • Install the two 8mm bolts into the switch
    • Slide the shifter control arm onto the transmission selector shaft
    • Fasten the 15mm nut onto the shaft
    • Connect the neutral safety switch electrical connector

Tools needed for replacement:

    General Tools

  • Wire Brush

  • Materials, Fluids, and Supplies

  • Paper Towels

  • Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 15mm Socket
  • 8mm Socket

  • Wrenches - Metric

  • 15mm Wrench
  • 8mm Wrench
  • 12mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Neutral Safety Switch
This is a quality product. It was easily installed and resolved tightness in the shift column. Shipping was also fast.
November 21, 2017
Purchased
5 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
how does this switch unplug?
Edgar J on May 24, 2017
BEST ANSWER: Press the locking tabs on the wire plug as you pull it away from the old switch.a good spray of wd40 first helps.count the number of pins on plug to ensure you get the right switch. good luck Edgar.

Vehicle Fit

  • 1995-1996 Ford Bronco Neutral Safety Switch (11 Pin) 4 Speed Automatic Transmission
  • 1997 Ford E150 Van Neutral Safety Switch (11 Pin) for E4OD Automatic Transmission
  • 1998-2004 Ford E150 Van Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 1997 Ford E250 Van Neutral Safety Switch (11 Pin) for E4OD Automatic Transmission
  • 1998-2004 Ford E250 Van Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 1997 Ford E350 Van Neutral Safety Switch (11 Pin) for E4OD Automatic Transmission
  • 1998-2004 Ford E350 Van Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 1997 Ford E450 Van Neutral Safety Switch (11 Pin) for E4OD Automatic Transmission
  • 1998-1999 Ford E450 Van Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 2000-2005 Ford Excursion Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 1997-2002 Ford Expedition Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 2004 Ford F150 Heritage Truck Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 1996 Ford F150 Truck Neutral Safety Switch (11 Pin) for E4OD Automatic Transmission
  • 1997-2003 Ford F150 Truck Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 1997-1999 Ford F250 Light Duty Truck Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 1999-2004 Ford F250 Super Duty Truck Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 1996 Ford F250 Truck Neutral Safety Switch (11 Pin) for E4OD Automatic Transmission
  • 1999-2004 Ford F350 Super Duty Truck Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 1996-1997 Ford F450 Truck Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 2002 Lincoln Blackwood Neutral Safety Switch (11 Pin) for 4R100 Transmission
  • 1998-2001 Lincoln Navigator Neutral Safety Switch (11 Pin) for 4R100 Transmission

This part replaces:

  • OE # F7TZ7F293AA
  • OE # F7TZ7A247AA
  • Standard Motor Products NS126T
  • Dorman 511-101
Part #: 1AZNS00008

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(08:26 min)