Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Mirror Signal Type:   Upgrade LED Turn Signal
  • Mirror Operation:   Power
  • Mirror Color / Finish:   Chrome & Textured Black Caps
  • Mirror Folding Type:   Power-Folding
  • Mirror Heating Type:   Heated
  • Mirror Puddle Light Type:   Puddle Light

Specifications:

  • Fits RH (Passenger Side)
  • Power operation glass
  • Upgradeable LED turn signal
    • Instructions included
  • Folding - power operation
  • Puddle light
  • Textured black & chrome finish caps included
  • Without memory function
  • Without auto-dimming feature

PLEASE NOTE:  This mirror is not a stock option and will only replace units that have been upgraded to an aftermarket towing style mirror.

Upgraded Mirrors Note:

  • This set of upgraded mirrors are designed to fit and function just like the original. However, if the vehicle did not come equipped with all of the features noted, additional wiring may be required for complete operation.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Pin Insertion Instruction

  1. step : Removing the Door Panel (0:56)
    • Pry off the trim piece inside the door handle with a flat blade screwdriver
    • Pry up the window switch panel with a flat blade screwdriver
    • Disconnect the door lock wiring harness
    • Disconnect the window switch wiring harness
    • Pry off the speaker cover with a flat blade screwdriver
    • Remove the two 10mm bolts inside the door handle
    • Remove the 10mm bolt behind the screw panel
    • Remove the 6mm bolts from the speaker
    • Remove the two 10mm bolts at the bottom of the door panel
    • Pry off the speaker
    • Disconnect the speaker wiring lead
    • Remove the gasket from the speaker area
    • Remove the two speaker screw grommets with pliers
    • Lift the door panel up and off
    • Disconnect the latch cables from the door handle
  2. step : Removing the Side View Mirror (2:42)
    • Disconnect the side view mirror wiring harness
    • Remove the three 10mm nuts from the mirror
    • Remove the side view mirror
  3. step : Installing the Tow Mirrors (3:06)
    • Tighten the 10mm nuts on the tow mirrors by hand
    • Connect the mirror wiring harness
  4. step : Removing the Fuse Panel Cover (3:34)
    • Pull up on the side carpet trim
    • Pull the weather strip off of the door
    • Pull back on the kick panel near the door jamb
    • Pull off the side dash panel
    • Remove the fuse panel cover
  5. step : Connecting the Switch Wiring Harnesses (4:31)
    • Push in on the door connector tab near the door jamb and pull the grey connector down
    • Pull the door in and out to release the harness connection
    • Remove the rubber boot from the door
    • Poke a hole in the rubber boot with a flat blade screwdriver
    • Insert the signal wires into the hole and through the rubber boot
    • Carefully peel back the water shield
    • Pull the signal wires through the door
    • Connect the signal wires to the tow mirror
    • Repeat the process for the power-fold wiring harness
    • Wire-tie the new harnesses to the existing harness
    • Insert the rubber boot into the door
    • Plug in the door harness to the body
    • Repeat the process for the other side
  6. step : Wiring the Connectors (8:08)
    • Place electrical tape on the pinch weld
    • Run the wiring through the pinch weld
    • Press the weather strip in place
    • On the driver side bring the wiring up into the dash
    • Pull off the lower panel on the center console on both sides
    • Run the power fold wiring from the passenger side to the driver side
    • Insert the marker wiring and parking light wiring from the driver side to the passenger side
  7. step : Installing the Switch (10:20)
    • Cut out a template that's the same size as the switch
    • Draw a line around the template on the lower dash panel
    • Drill a hole on each side within the line
    • Shape the hole with a Dremel tool
    • Feed the switch harness in through the back
    • Plug in the switch harness and insert the switch in place
    • Wire-tie any hanging wire behind the lower dash panel
    • Remove one of the 10mm bolts from the body
    • Insert the ground wire to the bolt
    • Tighten the 10mm bolt to the body
  8. step : Installing the Fuse Tab (11:48)
    • Lower the glove box
    • Push in the tabs on the glove box and bring it down
    • Remove a 10mm bolt from the body
    • Run the ground wire into the bolt
    • Tighten the 10mm bolt to the body
    • Cut the marker wiring to the same length
    • Strip about a half inch on the end of the wiring
    • Twist the wiring together
    • Strip about a half inch from the power folding wire
    • Twist the power folding wiring
    • Insert the power folding wiring into the fuse tab
    • Insert the marker wiring into the fuse tab
    • Plug the lights into headlamp #23
    • Plug the power fold fuse into #4
    • Push on the fuse cover
    • Test the mirrors
  9. step : Reinstalling the Side Panels (16:15)
    • Push on the lower panels on the center console
    • Push the kick panel in place
    • Push on the side carpet trim
    • Push in the side dash panel
  10. step : Reinstalling the Door Panel (16:55)
    • Put the water shield into place
    • Connect the latch cables to the door handle
    • Lift the door panel into place
    • Push in the door panel clips
    • Push in the speaker clips
    • Put on the lower gasket
    • Connect the speaker wiring lead
    • Insert the speaker into place
    • Tighten the 6mm screws to the speaker
    • Tighten the two 10mm screws on the bottom of the door panel
    • Tighten the 10mm screw behind the switch panel

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Electrical Tape

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Wire Cutters

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 6mm Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Can i just buy the cap for these mirrors?
John D April 13, 2016
Year Make Model Description
2004Ford F150 Truck Ford F150 Truck New Body Style Power Heated Upgrade LED Turn Signal Puddle Light Power-Folding Chrome & Textured Black Caps Mirror Passenger Side
2005-2008Ford F150 Truck Ford F150 Truck Power Heated Upgrade LED Turn Signal Puddle Light Power-Folding Chrome & Textured Black Caps Mirror Passenger Side
2006-2008Lincoln Mark LT Lincoln Mark LT Power Heated Upgrade LED Turn Signal Puddle Light Power-Folding Chrome & Textured Black Caps Mirror Passenger Side
Part #: 1AMRE02937


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(19:17 min)