These replacement suspension parts are just what you need to get your vehicle in good working order again.

Specifications:

  • 8 Piece Suspension Kit includes:
    • (2) - FRONT Strut & Spring Assemblies - LH (Driver Side) & RH (Passenger Side)
    • (2) - REAR Shock Absorbers - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT Sway Bar Links - LH (Driver Side) & RH (Passenger Side)
    • (2) - REAR Sway Bar Links - LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Accessing the Strut (0:53)
    • Remove the lug nuts
    • Pull the wheel free
    • Apply penetrating oil to the bolt holding the lower strut and the upper bolt holding the stabilizer link
    • Remove the clip holding the brake hose to the strut (Use a screwdriver to pry up from below)
    • Pull the hose free
    • Lock locking pliers on the backside of the stabilizer shaft
    • Remove the 14mm bolt
    • Spray the 17mm bolt holding the steering knuckle to the strut with penetrating oil
    • Remove the 17mm bolt using the pipe for extra leverage
  2. step : Removing the Strut (3:11)
    • Spray penetrating oil around the bottom of the strut
    • Hit the steering knuckle with a sledge hammer
    • Once the knuckle moves, place a piece of wood over the knuckle and hammer the rest of the way
    • Remove two of the bolts holding the strut from the back of the engine. Loosen the third bolt
    • Push down on the steering knuckle and push the bottom free
    • Remove the third screw up top to free the strut
  3. step : Replacing the Strut (4:29)
    • Line the strut up with the bolt holes up top. Replace the three bolts firm but not fully tightened
    • Spray penetrating oil on the strut and steering knuckle
    • Once its lined up but a jack underneath the knuckle and use it to force it into place
    • Replace the bolt holding the knuckle to the strut. (Use a torque wrench to tighten it to 80 ft/lbs)
    • Bring the hose down and feed it through into place. Replace the clip
    • Reconnect the stabilizer link. Using locking pliers on the back, thread the nut on and tight to 50-60 ft/lbs
    • Replace the wheel
    • Replace lug nuts, and tighten to 100 ft/lbs. in a star pattern
    • Tighten the upper strut bolts to 25ft/lbs

Tools needed for replacement:

    General Tools

  • Sledge Hammer
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 17mm Socket
  • 14mm Socket
  • 18mm Socket
  • 19mm Socket
  • 15mm Socket
  • 13mm Socket
  • 16mm Socket

4.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
1
0
0
Fits like a glove.
Ordered from 1aauto for first time and came in as promised. I replaced them myself then aligned the wheels. Now it drives nice like a new sporty car. Love it. Indeed will come back and order from them again.
June 24, 2017
Purchased
10 months ago
Almost perfect
I installed this kit in my 2010 Mazda 5 sport. I gave the review only 3 stars because I did run into some issues with the front struts. I had trouble with the brackets that are supposed to hold the brake lines. The opening was too small and the metal was a bit too thick to accept the factory fitting. I had to bend them wide open and tap the brake line in with a screwdriver and hammer and then bend it back into position. Also, the bolts for the top of the assembly are far shorter than the factory bolts. I had some trouble using the factory bolts and had to use the supplied bolts in a few of the holes which were not easy to get in. The rear shocks were easy peasy, as were the end links. The car rides almost like new now.
September 25, 2017
Purchased
5 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 4 answers
What brand are these part?
David B on Mar 17, 2017
BEST ANSWER: We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle. If you have any further questions, please don't hesitate to ask.
Do you have any suspension for a 2008 mazda speed 3?? I can't find any I'm your page.
Mrrojas on May 5, 2016
BEST ANSWER: Not at this time

How-to Video:

(07:42 min)

Tools List:

    General Tools

  • Sledge Hammer
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 17mm Socket
  • 14mm Socket
  • 18mm Socket
  • 19mm Socket
  • 15mm Socket
  • 13mm Socket
  • 16mm Socket



This part replaces:

  • Moog K80867
  • Moog K80235
  • Beck Arnley 101-5264
  • OE # BP4K-28-170H
  • OE # 31351095695, 31351091496
  • Reference Number 663283
  • Monroe 172264
  • Monroe 172263
  • Monroe 5607
  • KYB 343412

Vehicle Fit

  • 2004-2006 Mazda 3 Front & Rear Suspension Kit 8 Piece Set
  • 2007-2009 Mazda 3 Front & Rear Suspension Kit 8 Piece Set excluding Speed Model
  • 2006-2010 Mazda 5 Front & Rear Suspension Kit 8 Piece Set
Part #: 1ASFK01990

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More