Replaces

Lexus RX300 Toyota Highlander Radiator Dual Cooling Fan Assembly - 1ARFA00183

Our aftermarket radiator fan assemblies are some of the highest quality replacements on the market! This radiator cooling fan assembly is a complete, ready to bolt on, direct replacement part.

Specifications:

  • New, not rebuilt, electric motor
  • Geometrically designed plastic blade for optimal circulation and uniform balance
  • Shroud designed to ensure structural integrity and endurance for maximum performance
  • 100% Performance factory tested
  • Replaces original assemblies that are melted or worn out
  • Comes with proper plug(s) for trouble free installation

Now you can buy a high quality radiator cooling fan motor assembly that is built to strict quality control standards. This cooling motor assembly makes a great replacement and has good cost savings over a dealer fan assembly.

Returns Note:

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Draining the Radiator (0:27)
    • Raise and support the vehicle
    • Apply rust penetrant to the eight 10mm bolts on the splash shield
    • Remove the eight 10mm bolts from the splash shield
    • Pry the two push clips out of the splash shield with a flat blade screwdriver
    • Pull the splash shield down and off
    • Have a drain pan ready
    • Unscrew the radiator drain by hand
    • Twist off the radiator cap
    • Allow the radiator to drain
    • Close the radiator drain
  2. step : Disconnecting the Radiator Lines (2:42)
    • Loosen the transmission cooler line clamps with pliers
    • Disconnect the transmission cooler lines from the radiator
    • Attach the finger of a glove to the hose and connector with a zip tie to prevent leaking
    • Loosen the lower radiator hose clamp with pliers
    • Disconnect the lower radiator hose from the radiator
    • Carefully disconnect the overflow hose from the radiator
    • Loosen the upper radiator hose clamp with pliers
    • Disconnect the upper radiator hose from the radiator
  3. step : Removing the Radiator (5:20)
    • Disconnect the radiator fan electrical connectors
    • Remove the 12mm bolts from the radiator brackets
    • Remove the radiator brackets
    • Lift the radiator up and out of the engine bay
  4. step : Removing the Radiator Fan (6:10)
    • Remove the six 10mm bolts that hold the fan assembly to the radiator
    • Pull the fan assembly off the radiator
  5. step : Connecting the New Fan to the Radiator (6:58)
    • Line up the new fan on the radiator
    • Fasten the six 10mm bolts that hold the fan assembly to the radiator
  6. step : Installing the Radiator (7:16)
    • Remove the rubber grommets from the radiator
    • Place the grommets on the radiator support
    • Lower the radiator onto the grommets
    • Line up the radiator brackets
    • Insert the two 12mm bolts into the radiator brackets
    • Connect the radiator fan electrical connectors
  7. step : Connecting the Radiator Lines (9:05)
    • Connect the upper radiator hose to the radiator
    • Tighten the upper radiator hose clamp with pliers
    • Connect the overflow hose to the radiator
    • Connect the lower radiator hose to the radiator
    • Tighten the lower radiator hose clamp with pliers
    • Remove the zip ties and glove fingers from the transmission cooler lines with side cutters
    • Connect the transmission cooler lines to the radiator
    • Clean any fluid off the radiator with paper towels
    • Top off the transmission fluid
    • Tighten the transmission cooler line clamps with pliers
  8. step : Filling the Radiator (10:40)
    • Twist off the radiator cap
    • Add coolant to the radiator using a funnel
    • Turn the heat to hot, but do not run the fan
    • Run the engine to clear air bubbles from the cooling system
    • Add coolant as necessary
    • Add coolant to the overflow bottle as necessary
    • Twist on the radiator cap
  9. step : Installing the Splash Shield (12:12)
    • Lift the splash shield into place
    • Insert the two push pins into the splash shield
    • Insert the eight 10mm bolts into the splash shield

Tools needed for replacement:

    General Tools

  • Funnel
  • Pick
  • Drain Pan

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Gloves
  • Paper Towels
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Side Cutters
  • Slip-Joint Pliers
  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2001-2003Lexus RX300 Lexus RX300 Radiator Dual Cooling Fan Assembly for Models with 7 Blade Fan
2001-2007Toyota Highlander Toyota Highlander Radiator Dual Cooling Fan Assembly L4 2.4L with 7 Blade Fan
2001-2003Toyota Highlander Toyota Highlander Radiator Dual Cooling Fan Assembly V6 3.0L
2004-2007Toyota Highlander Toyota Highlander Radiator Dual Cooling Fan Assembly V6 3.3L without Tow Package (excluding Hybrid Models)

This part replaces:

  • Hollander 674-59644A
  • Dorman 620-551
  • Partslink TO3115128
  • TYC 620810
  • DEPO 312-55038-000
Part #: 1ARFA00183


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(13:10 min)