Replaces

Jeep Wheel Hub Bearing & Axle Kit TRQ BHA52930 - 1AAHK00013

Specifications:

  • Brand New Wheel Bearing & CV Axle Kit
  • Comes as a 4 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

 

 

Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:51)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Straighten the cotter pin on the axle nut with needle nose pliers
    • Remove the cap and washer from the axle nut
    • Loosen the axle nut with a 36mm socket and breaker bar
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Rotor (2:18)
    • Remove 13mm bolts from the brake caliper
    • Pull the caliper aside and secure it out of the way with a bungee chord
    • Pull the rotor off
  3. step : Removing the Hub (3:10)
    • Spray rust penetrant around the contact points of the hub
    • Remove the three 13mm 12-point bolts from the hub
    • Pry off the washer from the axle (if you have one) with a pick
    • Tap the axle in with a hammer to free the splines from the hub
    • Tap the hub out of the spindle with a hammer
    • Remove the hub and dust shield
  4. step : Installing the Hub (5:55)
    • Insert the dust shield into place
    • Insert the hub into place
    • Tighten the 12-point 13mm bolts
    • Torque the hub bolts to 75 foot-pounds
  5. step : Installing the Rotor (6:49)
    • Insert the rotor onto the hub
    • Press the caliper onto the rotor
    • Tighten the two 13mm bolts to the caliper
    • Torque the caliper mounting bolts to 20 foot-pounds
  6. step : Reattaching the Wheel (7:28)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 110 foot-pounds in a crossing or star pattern
    • Torque the axle nut to 175 foot-pounds
    • Insert the axle nut cap into place
    • Insert a new cotter pin into place
    • Turn each end of the cotter pin to opposite sides of the nut

Tools needed for replacement:

    General Tools

  • Hammer
  • Pick

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 19mm Socket
  • 13mm Socket
  • 36mm Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Hub and axle shifts
They fit perfectly and the quality of the parts were great and with the help of the tec when i was buying them the job when flawlessly
October 27, 2017
Purchased
6 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1993-1998 Jeep Grand Cherokee Front 4 Piece Set Wheel Hub Bearing & Axle Kit for Models with CV Joint Style Axles TRQ
  • 1993 Jeep Grand Wagoneer Front 4 Piece Set Wheel Hub Bearing & Axle Kit for Models with CV Joint Style Axles TRQ

This part replaces:

  • OE # 53007449, 53007449AB
  • TRQ BHA52930
Part #: 1AAHK00013



TRQ
Brand #: BHA52930

How-to Video:

(08:55 min)