Replaces

Jeep Liberty Wrangler Brake Kit Nakamoto CD981, 53010-DSZ - 1APBS00382

Brake Pad Specifications:

  • Premium Posi Ceramic brake pads
  • 4 Piece Rear brake pad set
  • Includes shims
  • Direct replacement

Brake Rotor Specifications:

  • Comes as a matched Pair
    •  Fits LH (Driver Side) & RH (Passenger Side) Rear
  • Cross drilled, Slotted, And Zinc Coated
  • Fits 5 lug wheels
  • Solid

Premium Positive Molded Brake Pads Features and Benefits:

  • The very same manufacturing process the original equipment manufacturers use
  • High density friction material for long pad life
  • Less resin content virtually eliminates brake fade and glazing
  • Reduced dusting for both Ceramic and Semi-metallic materials
  • Quality multi-layered shims and pad chamfering provide smooth and quiet braking
Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

Zinc Coated

Zinc Coated to help reduce rust and corrosion for a longer-lasting and better looking rotor

"True" Non-Interference Vane Design

"True" Non-Interference Vane Design retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots are machined to remove brake dust and expel gasses during hard braking

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:41)
    • Pry off the wheel cover with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (0:58)
    • Check for gouges on both sides of the rotor
    • Check the thickness of the brake pads
    • Check the brake pad wear indicator
  3. step : Removing the Brakes (1:14)
    • Remove the two 13mm bolts from the brake caliper
    • Pry the caliper piston in with a flat blade screwdriver
    • Pull the caliper aside
    • Pry the brake pads out of the caliper with a flat blade screwdriver
    • Pull the rotor off
  4. step : Preparing the New Brake Pads and Rotors (2:04)
    • Clean the rotor with brake parts cleaner
    • Apply grease to the brake pad tabs
    • Clean the brake pad slides with a wire brush
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Check that the caliper slides move freely
    • If necessary, apply grease to the caliper slides
  5. step : Installing the New Brakes (3:11)
    • Slide the rotor on
    • Install the new brake pads into the caliper
    • Put the caliper on
    • Thread the two 13mm bolts by hand
    • Tighten bolts to between 20 - 25 foot-pounds of torque
  6. step : Reattaching the Wheel (4:22)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the wheel cover
  7. step : Testing the Brakes (4:54)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner
  • Bearing Grease

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2003-2007 Jeep Liberty Rear Premium Posi Ceramic Cross Drilled & Slotted Zinc Coated Performance Brake Kit Nakamoto
  • 2003-2006 Jeep Wrangler Rear Premium Posi Ceramic Cross Drilled & Slotted Zinc Coated Performance Brake Kit Nakamoto

This part replaces:

  • Nakamoto CD981, 53010-DSZ
Part #: 1APBS00382



Nakamoto
Brand #: CD981, 53010-DSZ

How-to Video:

(05:37 min)