Replaces

Jeep Liberty Wheel Bearing & Hub Assembly TRQ BHA85004 - 1ASHS01222

Part Details

  • Includes: (1) 35mm Axle Nut Socket
  • Wheel Bearing & Hub Assembly Features & Benefits:
    Direct Fit Replacement
    Precision Engineered
    Highest Quality Materials
  • Bearing Type: Ball Bearing

 

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:47)
    • Pry off the wheel cover with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:13)
    • Turn the rotor by hand or turn the steering wheel to turn the rotor
    • Pry the rotor back with a pry bar
    • Remove the two 12mm bolts from the brake caliper
    • Pull the caliper aside
    • Hang the caliper with wire ties
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (2:04)
    • Remove the two 21mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
  4. step : Removing the Wheel Hub (2:28)
    • Disconnect the ABS sensor wire from the wheel hub with a flat blade screwdriver
    • Pry the wire out of all its clips
    • Pry the wiring harness clip off of the stud inside the engine compartment
    • Disconnect the ABS wiring harness in the engine compartment
    • Pull the wiring out through the wheel well
    • Have an assistant hold the hub in place with a pry bar
    • Remove the 35mm hub nut
    • Remove the three E14 external Torx bolts from the hub
    • Thread the lower left E14 bolt 1/3 of the way in
    • Strike the hub with a hammer to loosen it
  5. step : Installing the New Wheel Hub (5:28)
    • Clean the hub mounting area with a wire brush
    • Apply brake grease to the new hub
    • Put the new hub into place
    • Insert the three E14 bolts into the hub
    • Tighten the three E14 bolts to 50 foot-pounds of torque
    • Have an assistant hold the hub in place with a pry bar
    • Fasten on the 35mm hub nut
    • Tighten the hub nut to 100 foot-pounds
    • Feed the new ABS wiring into place
    • Connect the ABS wiring harness at the wheel hub
    • Clip the wiring into place
    • Connect the ABS wiring harness in the engine compartment
    • Clip the ABS wiring on the stud in the engine compartment
  6. step : Reinstalling the Brake Rotor (8:04)
    • Slide the rotor on
    • Put the bracket back into place
    • Start the 21mm bolts by hand
    • Tighten the 21mm bolts to between 85 foot-pounds of torque
  7. step : Reinstalling the Brake Pads (8:41)
    • Install the new brake pads into the bracket
    • Cut the brake caliper free
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Put the caliper on
    • Thread the two 12mm bolts by hand
    • Tighten bolts to between 20 - 25 foot-pounds
  8. step : Reattaching the Wheel (9:40)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the wheel cover
  9. step : Testing the Brakes (10:14)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Large C-Clamp
  • Jack Stands
  • Assistant

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • A Piece of Pipe (for leverage)
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 35mm Socket
  • 19mm Socket
  • 21mm Socket

  • Torx Drivers & Sockets

  • E14 Inverted Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2002-2005Jeep Liberty Jeep Liberty with ABS Brakes Front Wheel Bearing & Hub Assembly Driver Side with (1) 35mm Axle Nut Socket TRQ
2006-2007Jeep Liberty Jeep Liberty Front Wheel Bearing & Hub Assembly Driver Side with (1) 35mm Axle Nut Socket TRQ

This part replaces:

  • TRQ BHA85004
Part #: 1ASHS01222


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: BHA85004

How-to Video:

(10:56 min)