Specifications:

  • Intake Manifold Gasket Set
  • Made from high quality materials
  • Direct replacements
  • Built to strict quality control standards
  • Correct for models with V6 2.7L Engine only

This gasket set makes a great replacement and has good cost savings over dealer gaskets.

Wear and Tear

This item is backed by a 60-day warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Release the pressure from the fuel system (0:51)
    • With the engine running, remove the fuel pump relay from the fuse block.
    • This will stop the engine and release the pressure in the fuel system.
  2. step : Remove the upper intake manifold. (0:59)
    • Use a 10 mm socket and ratchet to remove the upper intake manifold.
    • Disconnect the air pressure sensor.
    • Remove the 8 ten mm bolts.
  3. step : Remove the air box (1:40)
    • Loosen the clamp and the bolt securing the air box.
    • Disconnect the hose and wiring harness.
    • Remove the 13 mm bolt that goes into the throttle body and brace.
    • Pull the gasket off the top of the cowl and now you can remove your intake manifold.
  4. step : Remove the lower intake manifold. (2:17)
    • Pry up the gaskets.
    • Remove the four 10 mm bolts under the intake manifold to get at the fuel rails.
    • Disconnect the throttle position sensor if you need to.
    • Pull the fuel rails up and out.
    • Stuff a clean rag in the intake to keep anything from falling into it. (this would be bad)
    • Disconnect the wiring harness connectors from the injector.
    • Remove the lower intake manifold, having someone help hold the upper intake manifold out of the way.
    • Use a vacuum to remove any debris.
    • Remove the lower intake manifold gaskets.
    • Install the new gaskets.
  5. step : Reassemble the intake manifold (4:58)
    • Replace your lower intake manifold.
    • Push your fuel rails back into place.
    • Apply some loc-Tite to the four 10 mm bolts and snug them down with a socket and ratchet.
    • Bolt down the intake manifold.
    • Torque the 10 mm bolts to 105 inch/pounds, alternating the bolts you tighten working from the center out.
  6. step : assemble everything else (6:50)
    • Reconnect the air pressure sensor
    • Bolt in the 13 mm bolts securing the bracket to the throttle body, and torque to 15 foot/lbs
    • Reinstall the air box.
    • Tighten the clamp that connects the intake to the throttle body
    • Reconnect the hose and double check all of your sensors are connected.
    • Reinstall the fuel pump relay.
    • Seat the cowl gasket.

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Liquid Thread Locker

  • Ratchets & Related

  • Torque Wrench
  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(08:33 min)

Tools List:

    Materials, Fluids, and Supplies

  • Liquid Thread Locker

  • Ratchets & Related

  • Torque Wrench
  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 10mm Socket




Vehicle Fit

  • 2005-2009 Chrysler 300 Intake Manifold Gasket Set V6 2.7L
  • 1998-2004 Chrysler Concorde Intake Manifold Gasket Set V6 2.7L
  • 2001-2009 Chrysler Sebring Intake Manifold Gasket Set V6 2.7L
  • 2008-2009 Dodge Avenger Intake Manifold Gasket Set V6 2.7L
  • 2006-2009 Dodge Charger Intake Manifold Gasket Set V6 2.7L
  • 1998-2004 Dodge Intrepid Intake Manifold Gasket Set V6 2.7L
  • 2005-2008 Dodge Magnum Intake Manifold Gasket Set V6 2.7L
  • 2001-2006 Dodge Stratus Intake Manifold Gasket Set V6 2.7L
Part #: 1AEGS00267

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More