Replaces

Infiniti G35 Nissan 350Z Steering & Suspension Kit - 1ASFK04114

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as an 10 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:55)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:15)
    • Measure the distance from the end of the boot to the center of the top of the tie rod
    • Note that measurement
    • Apply penetrating oil to the tie rod lock nut
    • Hold the inner tie rod with a 13mm wrench
    • Loosen the locking nut with an adjustable wrench
    • Turn the wheel by hand or with the steering wheel for better access to the tie rod
    • Remove the cotter pin with needle nose pliers
    • If you cannot remove the cotter pin, sheer it off by removing the 19mm bolt
    • Remove the 19mm bolt
    • Loosen the tie rod from the spindle by striking the spindle with a hammer
    • Pull the outer tie rod out of the handle
    • Hold the inner tie rod with a 13mm wrench
    • Twist off the outer tie rod by hand
  3. step : Installing the New Outer Tie Rod (3:52)
    • Apply anti-seize grease to the inner tie rod
    • Hold the inner tie rod with a 13mm wrench
    • Twist the outer tie rod on by hand
    • Measure the distance from the end of the boot to the center of the top of the tie rod
    • This should equal the measurement recorded in Step 2
    • Push the outer tie rod into the spindle
    • Start the tie rod nut by hand
    • Tighten the nut to 55 foot-pounds of torque
    • Line the tie rod hole up with one of the slots in the nut
    • Insert the cotter pin and bend it to lock it
    • Hold the inner tie rod with a 13mm wrench
    • Tighten the locking nut with an adjustable wrench
  4. step : Reattaching the Wheel (6:35)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large Hammer

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Lug Wrench
  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket
  • 21mm Socket

  • Wrenches - Metric

  • 13mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005-2007 Infiniti G35 Coupe Rear Wheel Drive 10 Piece Set Steering & Suspension Kit
  • 2005 Nissan 350Z (Built After 7/04 Production Date) 10 Piece Set Steering & Suspension Kit
  • 2006-2009 Nissan 350Z 10 Piece Set Steering & Suspension Kit

This part replaces:

  • Hollander 512-58685R
  • Hollander 512-58686L
  • Hollander 512-58883R
  • Hollander 512-58884L
  • Hollander 512-58916R
  • Hollander 512-58917L
  • OE # 48520AM625
  • OE # 48640AL585
  • OE # 54468CD00C
  • OE # 54469CD00C
  • OE # 54500AM602
  • OE # 54501AM602
  • OE # 54618AL501
  • OE # 54618AL502
  • OE # 54668AL501
  • OE # 54668AL502
  • Dorman 521-601
  • Dorman 521-602
  • Dorman 521-603
  • Dorman 521-604
  • Moog K750044
  • Moog K750047
  • Moog ES80579
  • Moog ES80578
  • Moog K750101
  • Moog K750100
  • Moog K642009
  • Moog K642008
  • Moog K621373
  • Moog K621372
  • Beck Arnley 101-5920
  • Beck Arnley 101-5919
  • Hollander 512-58917L, 512-58884L
  • Hollander 512-58916R, 512-58883R
Part #: 1ASFK04114



How-to Video:

(07:13 min)