This is the ignition switch that mounts inside the steering column.

  • Common Problems
  • Damaged during a theft attempt
  • No start condition occur because the junction block contacts corrode and short out.
  • No start condition because the contacts in the rotating upper assembly wear out
  • While Driving your gauges and dash lights flicker as if the vehicle shuts off for a brief second

If your vehicle is having issues when starting such as the power comes on in the car when you turn the key on but then the engine does not turn over or if accessories don't seem to work and you've checked things like the battery and fuses this part may be your problem. If your contacts are corroded you can clean them but once the protective coating is gone then they will most likely corrode again quicker and possibly short out. If you are having problems with this part then fix it right the first time.

  • Mounts inside the steering column and connects to the lock cylinder and main column harness, When the key cylinder is turned, it turns the switch on this harness that sends the electrical single to start the vehicle
  • Replaces dealer part numbers: 35130S30003, 35130-S30-003, 35130SV4003, 35130-SV4-003
  • Exact fit
  • No cutting or splicing necessary
  • 7 Terminal Connection
  • Fits all tilt and non tilt columns

 

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

 

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Disconnect the Negative Battery Cable (0:54)
    • Remove the negative terminal with a ratchet
  2. step : Remove the Steering Column Trim (1:00)
    • Remove the three screws securing it
    • Pull off the trim
  3. step : Remove the Ignition Switch (1:57)
    • Remove the two bolts using your 8mm socket and ratchet
    • Unplug the wiring harness
    • Unscrew the Phillips screw to remove the switch
  4. step : Reassemble the Steering Column Trim (3:20)
    • Put the switch back on the ignition piece and screw it back in
    • Plug all the wiring back in
    • Bolt the ignition piece back into the steering column
    • Replace the steering column trim and bolt it back on
    • Reconnect the battery

Tools needed for replacement:

    Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 8mm Socket

5.0 / 5.0
4 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
4
0
0
0
0
fit like the old part
shipping was fast and part fit just like the old one. Replacement video was a little off. In video it shows a 99 model. Mine was a 97 model and did not have the bolts on top of steering column. Had to break old part to get it out and remove cover on new part to get it to fit back in.
March 22, 2018
Purchased
4 months ago
Awesome!!!!
Perfect direct fit ,high quality part, very fast shipping, very Best priced....
January 12, 2018
Purchased
6 months ago
Fits 1998 Honda Prelude type SH
It fits my Honda Prelude PERFECTLY!

I was having issues with the car stalling on startup, and stalling without warning while I was driving. This was due to the electrical contacts being worn out on the original ignition switch, thus causing the electrical current to cut out and, subsequently stalling my car without warning... While I'm driving, on the throttle, just cruising. Very dangerous if it happened while I was turning out into a gap in traffic.

I called Honda, we ran my VIN and they said that the ignition switch had been replaced already... hah, bullsh*t. Well, maybe the one they replaced it with wore out.

For a total cost after shipping and taxes of $50 CAD, I took things into my own hands. It was worth every cent.

Don't be afraid of installing this people, it's dead easy. I know nothing about cars and I still did it.

Just make sure you have an L-shaped Phillips screwdriver on hand or something of the sort if your car is a Prelude -- I had one HELL of a screw to deal with.

1A Auto, your shipping prices are abysmal but you guys rock. Thank you for helping me make my car safer :)

7th December 2017
December 7, 2017
Purchased
8 months ago
Great
Great service, price and delivery Great service, price and delivery Great service, price and delivery Great service, price and delivery!
July 18, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
My 96 accord dosent have the 8mm head on the screws hoe do I take them off?
Miggs on Mar 4, 2017
BEST ANSWER: If there are no screws holding this piece on, we would ask if there is a separate screw, or rivet. This will be required to remove the switch from your vehicle.

Vehicle Fit

  • 1997 Acura CL Ignition Switch
  • 1995-1998 Acura TL Ignition Switch
  • 1994-1997 Honda Accord Ignition Switch
  • 1997 Honda Prelude Ignition Switch

This part replaces:

  • Standard Motor Products US-288T
Part #: 1AZIS00012

How-to Video:

(06:29 min)