This ignition switch is just what you need to get your vehicle running again!

Specifications:

  • Electrical switch
  • Steering Column mounted
  • Replaces dealer part numbers: 26036311
  • Exact fit
  • No cutting or splicing necessary
  • Built to strict quality control standards

This item is an electrical part. These units are tested prior to shipment.

Our electrical and electronic parts are subject to strict quality control testing .  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Disconnecting the Battery (0:50)
    • Remove the negative terminal with a 5/16 or 8mm wrench
  2. step : Removing the Air Bag (1:23)
    • Pry the pins up and out from behind the steering wheel
    • Disconnect the air bag wiring harness
    • Remove the orange safety
  3. step : Removing the Steering Wheel (2:23)
    • Insert the seat belt through the steering wheel
    • Click in the steering wheel
    • Crack the 21mm bolt loose
    • Release the seat belt and remove it from the wheel
    • Finish removing the 21mm nut
    • Wiggle the wheel up and off by hitting the back sides or use a puller
  4. step : Removing the Steering Column Cover and Ignition Cylinder (4:07)
    • Remove the snap ring on the clock spring with a pair of snap ring pliers
    • Tilt the column all the way up
    • Remove the lever by pulling it out
    • Remove the two T25 Torx screws on the bottom of the cover
    • Pull the lower column down
    • Remove the two inverted Torx screws with an inverted E5 socket
    • Reinstall the tilt lever
    • Push down the column
    • Remove the lever
    • Push down the small hole in the top of the ignition cylinder with a hooked pick
    • Hold the key the key in the cylinder and press the hole to pull out the cylinder and remove the upper cover
  5. step : Removing the Lower Dash Panel (6:53)
    • Remove the four 7mm screws along the bottom near panel
    • Pop the panel and its plastic clips out
    • Pull out the e-brake release handle
    • Compress the tabs on each side of the release handle
    • Turn the e-brake and slide the cable out
  6. step : Removing the Ignition Starter Switch (8:19)
    • Remove the four 10mm bolts from the metal knee pan
    • Remove the metal knee panel
    • Release the tab and rotate the sensor from the ignition cylinder
    • Remove the two E4 inverted Torx with an E4 inverted Torx socket
    • Remove the ignition starter switch from the column
    • Unclip the harness wiring from any retainers/clips
    • Peel open the wrap around the harness to separate it
    • Remove the 7mm bolt in the middle of the ignition switch harness
    • On the side of the connector for the ignition switch, remove the 7mm screw
    • Slide the connector up and out
    • Pry the connector out of the main connector
    • Remove the switch
  7. step : Installing the Ignition Starter Switch (12:28)
    • Insert the switch and harness into place
    • Reinstall the two E4 inverted Torx screws
    • Clip in the harness to the ignition coil
    • Plug in the harness to the main connector
    • Reinstall the 7mm screws to the switch
    • Reattach the vent
  8. step : Installing the Lower Dash Panel (15:10)
    • Insert the metal dash panel into place
    • Tighten the bolts to the metal
    • Pull the e-brake cable back through the opening and twist it to lock it
    • Press the panel into place
    • Tighten the four 7mm screws along the bottom of the panel
  9. step : Installing the Steering Column Cover (16:10)
    • Reinstall the upper column cover
    • Insert the cylinder into place with the key in
    • Turn it forward and back to engage
    • Reinstall the tilt lever
    • Raise the column slowly
    • Reinstall the two E5 inverted Torx screws
    • Remove the tilt rod
    • Slide the lower column into place
    • Tighten the two T25 Torx screws
    • Reinstall the tilt lever
  10. step : Reinstalling the Steering Wheel (18:15)
    • Thread the harness through the steering wheel
    • Remove the alignment pin from the clock spring
    • Insert the wheel to the splines
    • Tighten the 21mm nut
    • Torque the nut to 29 foot-pounds
  11. step : Reinstalling the Air Bag (18:59)
    • Clip in the harness
    • Connect the harness to the air bag
    • Install the safety ball
    • Clip in the air bag and push it in
  12. step : Reconnecting the Battery (19:45)
    • Put your key in and turn it to the run position
    • Connect the negative terminal with an 8mm wrench

Tools needed for replacement:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Snap Ring Pliers
  • Side Cutters

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 7mm Socket

  • Torx Drivers & Sockets

  • E5 Inverted Torx Socket
  • T25 Torx Driver

4.7 / 5.0
12 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
11
0
0
0
1
Awesome
I was impressed across the board with their customer service, prices and prompt delivery . And would you believe it was actually the right part that I ordered so I think they're great thank you very much .
January 30, 2018
Purchased
2 months ago
Fantastic price!
I checked several local and online shops for this part and no one beat the price of 1AAuto, not to mention free shipping! Product received as expected, no trouble installing, works like a charm!
March 7, 2017
Purchased
1 year ago
5 star
Was a life saver to get this for the price it worked and fit just right no problems switched it out with a 1a auto Video off of YouTube
February 19, 2017
Purchased
1 year ago
The Berries
This part was the berries! It was what I needed to make it go.
I got it very fast. 1A Auto shipped the same day and I got it in 2 more. That's called 'kickin' it up here. I did all of the installation I could, but I had to get my son to make the under dash connection for me. I'm too fat to get into some places.
This part, and a couple more, made it all work again.
Not to forget...The price was lower than ANYONE ELSE!
Thank You,
RnJ Clark
July 8, 2017
Purchased
9 months ago
Lowest price I could find!
Seems to be high quality. Went in just like the original. Still working. I am happy.
August 26, 2017
Purchased
6 months ago
Speedo + Shifting Working Again
My speedo was wacky at times (100mph standing still) truck would stay stuck driving in 3rsd gear, shift indicator light would go out. - - - all because this switch went bad. This replacement went right in, fits perfect & works perfect, & at a much better price!! It takes a bit of work & time to swap out, works great now!!
January 20, 2018
Purchased
1 month ago
Ignition Starter Switch for 95 suburban
Great so far...fast shipping and easy to install. Fit was perfect. Pricing was way better than local companies who would of ordered the part for me. I highly recommend 1aauto.
July 25, 2017
Purchased
8 months ago
excellent product
went in effortlessly and worked perfect.no issues with this product.
February 9, 2018
Purchased
4 weeks ago
Well made
Fit perfectly. The switch is very well made.The video was great. The step by step instructions in the video simplified the installation.
July 1, 2017
Purchased
9 months ago
Happy Camper
I received the new cable Saturday much sooner than expected and much appreciated as it allowed me to install it Sunday afternoon. The installation video in conjunction with the price was the two primary reasons I purchased from 1A. The installation went just as described except that it was not necessary to remove the steering wheel. I believe the old switch was intermittent, so I haven't had enough opportunity to determine if the switch solved my problem. The cable matched perfectly.
February 19, 2018
Purchased
2 weeks ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 3 questions Browse 3 questions and 12 answers
Does this switch come with a new key?
Jordan on Oct 18, 2016
BEST ANSWER: This is just the actual ignition switch. If you're needing the keyed part as well that's usually called the ignition lock cylinder.
Will the 96 chevy k1500 ignition switch fit in a 98 k1500? Vehicle isn't starting and looking to do it myself cheap.
Seanw on Mar 1, 2017
BEST ANSWER: This will not mount on your 1998 model K1500. There are wiring differences, or connection differences.
The symptoms are: Speedometer and tachometer operate intermittently, and their malfunction coincides with the intermittent function of the automatic transmission. In other words, when the gauges fail, the transmission stays in ���drive��� (high) and does not start out in low then upshift. When the gauges work, so does the transmission. The problem seems to be electrical. Is the ignition switch suspect?
Randy B on Jan 4, 2017
BEST ANSWER: From the sounds of your issues, it appears that the issue would be more related to a vehicle speed sensor, or another piece of the electrical system. We do recommend having the vehicle diagnosed as there could be a fault towards the instrument cluster itself or the parts related.

How-to Video:

(20:28 min)

Tools List:

    General Tools

  • Pick

  • Materials, Fluids, and Supplies

  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Snap Ring Pliers
  • Side Cutters

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 7mm Socket

  • Torx Drivers & Sockets

  • E5 Inverted Torx Socket
  • T25 Torx Driver



This part replaces:

  • Hollander 633-00151
  • OE # 26036311
  • Standard Motor Products US-276

Vehicle Fit

  • 1995 Chevy Blazer S10 1st Design Ignition Starter Switch
  • 1995-1996 Chevy C1500 Truck 1st Design Ignition Starter Switch
  • 1995-1996 Chevy C2500 Truck 1st Design Ignition Starter Switch
  • 1995-1996 Chevy C3500 Truck 1st Design Ignition Starter Switch
  • 1995-1996 Chevy K1500 Truck 1st Design Ignition Starter Switch
  • 1995-1996 Chevy K2500 Truck 1st Design Ignition Starter Switch
  • 1995-1996 Chevy K3500 Truck 1st Design Ignition Starter Switch
  • 1995 Chevy S10 Pickup 1st Design Ignition Starter Switch
  • 1995-1996 Chevy Suburban C1500 1st Design Ignition Starter Switch
  • 1995-1996 Chevy Suburban C2500 1st Design Ignition Starter Switch
  • 1995-1996 Chevy Suburban K1500 1st Design Ignition Starter Switch
  • 1995-1996 Chevy Suburban K2500 1st Design Ignition Starter Switch
  • 1995-1996 Chevy Tahoe 1st Design Ignition Starter Switch
  • 1995-1996 GMC C1500 Truck 1st Design Ignition Starter Switch
  • 1995-1996 GMC C2500 Truck 1st Design Ignition Starter Switch
  • 1995-1996 GMC C3500 Truck 1st Design Ignition Starter Switch
  • 1995 GMC Jimmy S-15 1st Design Ignition Starter Switch
  • 1995-1996 GMC K1500 Truck 1st Design Ignition Starter Switch
  • 1995-1996 GMC K2500 Truck 1st Design Ignition Starter Switch
  • 1995-1996 GMC K3500 Truck 1st Design Ignition Starter Switch
  • 1995 GMC S-15 Sonoma 1st Design Ignition Starter Switch
  • 1995-1996 GMC Suburban C1500 1st Design Ignition Starter Switch
  • 1995-1996 GMC Suburban C2500 1st Design Ignition Starter Switch
  • 1995-1996 GMC Suburban K1500 1st Design Ignition Starter Switch
  • 1995-1996 GMC Suburban K2500 1st Design Ignition Starter Switch
  • 1995-1996 GMC Yukon 1st Design Ignition Starter Switch
Part #: 1AZIS00005

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More