Replaces

Ignition Lock Cylinder Kit Dorman 924-719 - 1AIMX00192

This ignition cylinder kit is just what you need to get your vehicle in good working order again.

Specifications:

  • Ignition Cylinder Kit includes:
    • Ignition Cylinder
    • Cylinder Tumblers
    • Cylinder Tumbler Springs
    • Retainer
    • Keys
  • Direct replacement
  • Built to strict quality control standards

This part makes a great replacement and has good cost savings over a dealer part.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Lower Panel (0:41)
    • Disconnect the negative battery cable with an 8mm socket
    • Push the tabs on the panel beneath the steering wheel
    • Remove the panel
    • Twist the socket and remove the bulb from the panel
    • Remove the two 7mm screws from the lower panel
    • Pull out the fuse panel door
    • Remove the lower panel by pulling on both sides
    • Remove the wiring harness from the lower panel with a flat blade screwdriver
  2. step : Removing the Steering Wheel Panels (1:47)
    • Remove the T25 screw from beneath the steering wheel
    • Pry out on the tilt lever on the lower steering wheel panel
    • Remove the lower steering wheel panel
    • Remove the two E5 External Torx bolts from each side of the upper panel
    • Remove the upper steering wheel panel
  3. step : Removing the Dash Panel (2:47)
    • Remove the fuse panel door
    • Remove the 7mm bolts from the fuse panel
    • Remove the 7mm bolt from the glove box
    • Pry off the key ignition bezel with a flat blade screwdriver
    • Pull out on either side of the dash panel
    • Pull the dash panel forward
    • Remove the hazard switch wiring harness with a flat blade screwdriver
    • Put the keys in the ignition
    • Turn it to the on position
    • Pull the shifter back all the way
    • Lift the dash panel up and out
  4. step : Removing the Ignition Lock Cylinder (4:15)
    • Remove the four 7mm bolts from the steel panel
    • Remove the four 10mm bolts from the steel panel
    • Remove the two 10mm bolts holding the ignition switch
    • Pull the ignition switch down through the steel panel's area
    • Put the key in the ignition, turn it on
    • Remove the ignition switch wiring harness with a flat blade screwdriver
    • Push in on the tab and pull the lock cylinder free
    • Remove the lock body harness
  5. step : Installing the Ignition Lock Cylinder (6:28)
    • Push in the piston on the inside of the lock body with your finger
    • Match the piston with the ignition harness and connect the wiring harness
    • Insert the key into the ignition
    • Turn the key to align the ignition with the lock body
    • Connect the ignition switch wiring harness
    • Turn the key to the off position
    • Remove the key
    • Reconnect the two wiring harnesses to the ignition
  6. step : Testing the Ignition (7:12)
    • Connect the negative battery cable with an 8mm socket
    • Place the key in the ignition and turn the vehicle on
  7. step : Replacing the Security (7:28)
    • Leave the car in the on position until the security light goes off
    • Turn the key off and wait six seconds
    • Turn the key on
    • Attempt to start the car once
    • Turn the car off
    • Repeat the process for two more times
    • You may need to jump start the car after three tries
  8. step : Installing the Ignition Switch (8:34)
    • Feed the ignition switch into its slot
    • Insert the two 10mm bolts holding the ignition
    • Replace the steel panel
    • Insert and tighten the four 7mm bolts
    • Insert and tighten the four 10mm bolts
  9. step : Reinstalling the Dash Panel (9:42)
    • Open the glove box
    • Turn the key to the on position
    • Pull the shifter back
    • Pull the steering wheel down
    • Tuck the dash panel behind the steering wheel
    • Connect the hazard switch wiring harness
    • Slide the shifter forward
    • Remove the key
    • Push in the clips on the dash panel
    • Replace the two 7mm bolts on the dash panel
    • Insert the ignition bezel
  10. step : Installing the Steering Wheel Panels (11:07)
    • Tilt the steering wheel down
    • Insert the upper steering wheel panel
    • Replace the E5 inverted Torx bolts
    • Insert the lower steering wheel panel
    • Insert the T25 screw from beneath the steering wheel
  11. step : Installing the Lower Panel (12:05)
    • Connect the wiring harness
    • Push in the lower panel
    • Insert the two 7mm screws from the lower panel
    • Push the bulb into the socket
    • Push in the tabs on the panel beneath the steering wheel
    • Push the tilt lever back into place
    • Push in the fuse panel door

Tools needed for replacement:

    Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket
  • 7mm Socket
  • 10mm Socket

  • Torx Drivers & Sockets

  • T25 Torx Driver
  • E5 Inverted Torx Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 2 answers
Once installed does it have to be programmed by a Chevy dealer ship?
Doris on Jul 26, 2017
BEST ANSWER: No, there will be an instruction sheet included to complete the replacement.
is this lock cylinder for a vehicle equipped with anti-theft?
carey w on Nov 13, 2016
BEST ANSWER: This part is nonspecific to anti-lock

How-to Video:

(13:30 min)

Tools List:

    Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket
  • 7mm Socket
  • 10mm Socket

  • Torx Drivers & Sockets

  • T25 Torx Driver
  • E5 Inverted Torx Socket



This part replaces:

  • OE # 15822350
  • OE # 25832354
  • Hollander 633-00157
  • Dorman 924-719

Vehicle Fit

  • 2004-2005 Chevy Classic Ignition Lock Cylinder Kit Dorman 924-719
  • 2000-2001 Chevy Impala Ignition Lock Cylinder Kit for Models with Floor Console Dorman 924-719
  • 2002-2005 Chevy Impala Ignition Lock Cylinder Kit Dorman 924-719
  • 2000-2001 Chevy Lumina Ignition Lock Cylinder Kit for Models with Floor Console Dorman 924-719
  • 1997-2003 Chevy Malibu Ignition Lock Cylinder Kit Dorman 924-719
  • 2000-2005 Chevy Monte Carlo Ignition Lock Cylinder Kit Dorman 924-719
  • 1999-2004 Olds Alero Ignition Lock Cylinder Kit Dorman 924-719
  • 1997 Olds Cutlass Ignition Lock Cylinder Kit excluding Supreme Models Dorman 924-719
  • 1998-1999 Olds Cutlass Ignition Lock Cylinder Kit Dorman 924-719
  • 1998-2002 Olds Intrigue Ignition Lock Cylinder Kit Dorman 924-719
  • 1999-2005 Pontiac Grand Am Ignition Lock Cylinder Kit Dorman 924-719
Part #: 1AIMX00192

Ships Same Day for orders placed by 4 P.M. ET

Dorman
Brand #: 924-719

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More