Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
TRQ ignition coils will have your engine running like new. TRQ ignition coils are manufactured to precise specifications using premium raw materials to optimize each vehicle's ignition system. To ensure peak performance, TRQ recommends replacing ignition coils in sets to prevent electrical output imbalances. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace ignition coil. On these vehicles, they recommend you replace these coils at 100,000 miles. Also, sometimes if your engine runs a little rough and turns the "check engine" light on and you get a code that says, "Cylinder 1 or Cylinder 3 or something misfiring," that's usually a coil going bad. It is a pretty easy replacement. You'll need a ratchet extension with 8mm and 10mm sockets. If you don't have an 8mm socket, a flat blade screwdriver can help you get the clamps off as you'll see.
Working from the passenger side, you want to remove two bolts that hold the top of the air box: one here and one right here. Now to remove this, you want to remove this intake tube which is a clamp here and a clamp here. Remove that tube and then loosen both this one and this one to pull this apart. I'll speed this up a little bit. You can either use a flat blade screwdriver or an 8mm socket with a ratchet and extension to undo those clamps. This also has a small vacuum line on here. Twist and pull that off, and then this goes up, and there's also a line right back here. Just pull off of there.
This big vehicle has been sitting for a while, so I'm just using a vacuum cleaner to clean up the vacated mouse house that's sitting on the intake. Okay, then take, twist, and get this collar off here. You can see here are our five coils. Pick any one of them, and just remove the 10mm bolt. Each of them have a little gray clip that you just pull on. Use a screwdriver. There's a little tab right in the center. Push the tab down and pull the clip right off.
Then there's just a tab for your thumb. Press that. Remove the lead, remove this 10mm bolt, and then, once you have the bolt removed, just move it around, shake it up and down a little bit, and then the coil comes up and out.
The new coil from 1A Auto is exactly the same as the old one. Put it right down in. You want to just push it straight in. Tighten up the 10mm bolt. Plug your lead back in, and then put the locking tab back in place. Repeat that for any cylinders you need. The cylinder order on these is usually just from front to back: 1, 2, 3, 4 and 5. If you get a code like "number 3 cylinder misfiring," that's usually a bad coil, so you'd replace the number 3 coil.
To put it back together, put this on there. There's a little notch that should stick up right there. I've got my two bolts already kind of in there. Right here is that hose. Push that hose down first. Put this down in place. I'm just kind of maneuvering it into this hose here. Push it into place and twist this hose a little bit off. Push it down onto here. Get it good and tight on there. Hook up the vacuum hose. Use an 8mm socket to tighten up. Just inspect where the hoses go and their housings. Make sure they're nice and tight, and then tighten up our clamps. Again, you can use either a flat blade screwdriver or an 8mm socket. Then we go back to our 10mm socket and then tighten them up and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an ignition coil on this 2003 GMC Envoy XL, with the 5.3 liter V8 engine. The items that you'll need for this is a new ignition coil from 1AAuto.com, 7mm socket and ratchet, and a flat blade screwdriver.
Because this is a V8, there's four ignition coils on either side of the engine, four here, and four more here. Each one is held in with two 7mm bolts. Start off by disconnecting the harness. Just lift up on the tab and disconnect it, and then pull and pry off the spark plug wire from the ignition coil, and then remove those two 7mm bolts. Once the bolt's removed, the ignition coil will pull right off.
On the left, is the old ignition coil; on the right, is the new one from 1A Auto. You can see they're identical, and will fit exactly the same. Wipe down the area where the ignition coil goes. Reconnect the harness to your ignition coil to help hold it into place, and then line it up on the bolt holes, and replace those two 7mm bolts, and tighten them up. Reconnect the plug wire, and repeat for any of the other coils you want to replace.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
