The ignition coil is a crucial part of your ignition system. It's function is to convert the 12 volt power of your vehicle's electrical system in to 35,000 or more volts. This produces a high intensity spark at the spark plug which then ignites the fuel in the cylinder. Coils in general will wear out over time. This will cause a misfire condition where the car looses power especially at higher engine RPM.

This Ignition Coil features the following specifications:

  • New not remanufactured
  • Replaces dealer part number: M05269670
  • Built to strict quality control standards
  • Direct replacement
  • 100% factory tested
  • Has a flat pin connector
    • Will not fit models with a oval or round plug connector
  • Fits 4 cylinder models

 

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function properly for your specific application.

Optimum Performance

Optimal performance, TRQ ignition coils are designed to meet or exceed the requirements of the vehicle.  TRQ ignition coils provide the correct primary and secondary resistance, voltage output, and spark energy that the vehicle needs to restore to its original operating condition.

Premium Quality

Manufactured with quality components and materials by using advanced technology to meet the highest quality control standards in the industry.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the ignition coil (1:04)
    • Remove the 13 mm socket with an extension and remove the intake manifold mounting bolts.
    • Use a 13 mm socket and ratchet to disconnect the EGR tube.
    • Now with an 8 mm socket and ratchet remove the 8 mm bolt on the EGR tube.
    • Take your 8 mm socket and extension, remove the five bolts securing the intake manifold.
    • Lift up the intake manifold and prop it up with a block of wood.
    • Unplug the spark plug wires.
    • If you are concerned about forgetting which order to plug them back in, use a marker to label them.
    • Disconnect the wiring harness connection.
    • Remove the four bolts and lift your coil up and out.
  2. step : Install the new ignition coil (7:23)
    • Mount the new ignition coil
    • Bolt it into place.
    • Connect the wiring harness.
    • Plug in the spark plug wires.
    • Carefully replace the intake manifold.
    • You may want to replace the intake manifold gasket to prevent a leak from forming, as unbolting the intake manifold deteriorates the gaskets sealing ability.
    • Bolt the five 8 mm bolts down, tightening them evenly.
    • Reconnect the EGR tube, bolting in the 8 and 13 mm bolts.
    • Replace the 13 mm mounting bolt.

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Block of Wood

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 8mm Socket
  • 13mm Socket
  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-2000 Chrysler Cirrus Ignition Coil L4 2.4L
  • 2001-2003 Chrysler PT Cruiser Ignition Coil
  • 1997-1999 Chrysler Sebring Ignition Coil L4 2.4L
  • 1997-1999 Chrysler Sebring Ignition Coil L4 2.0L
  • 2001 Chrysler Sebring Sedan Ignition Coil L4 2.4L
  • 2002-2003 Chrysler Sebring Sedan Convertible Ignition Coil L4 2.4L
  • 1997-1999 Dodge Avenger Ignition Coil L4 2.0L
  • 1997-2003 Dodge Caravan Ignition Coil L4 2.4L
  • 1997-2003 Dodge Neon Ignition Coil
  • 1996 Dodge Stratus Ignition Coil L4 2.0L with Flat Pin Connector
  • 1997-2000 Dodge Stratus Ignition Coil L4 2.0L
  • 1997-2000 Dodge Stratus Ignition Coil L4 2.4L
  • 2001-2003 Dodge Stratus Sedan Ignition Coil for with L4 2.4L
  • 1997-1998 Eagle Talon Ignition Coil excluding Turbo Models
  • 2002-2003 Jeep Liberty Ignition Coil L4 2.4L
  • 2003 Jeep Wrangler Ignition Coil L4 2.4L
  • 1997-1999 Mitsubishi Eclipse Ignition Coil L4 2.0L excluding Turbo Models
  • 1996 Plymouth Breeze Ignition Coil L4 2.0L with Flat Pin Connector
  • 1997-2000 Plymouth Breeze Ignition Coil
  • 1997-2003 Plymouth Voyager Ignition Coil L4 2.4L

This part replaces:

  • OE # 4557468
  • Standard Motor Products UF-189T
Part #: 1AECI00010

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(11:49 min)