Specifications:

  • Brand New Delphi Ignition Coil
  • Direct replacement
  • Built to strict quality control standard
  • 100% factory tested

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

The ignition coil pack is a crucial part of your ignition system. It's function is to convert the 12 volt power of your vehicle's electrical system in to 35,000 or more volts. This produces a high intensity spark at the spark plug which then ignites the fuel in the cylinder. Coils in general will wear out over time. 

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wiper Arms (0:25)
    • Pry the cap off the driver side wiper arm stud
    • Remove the 14m nut from the stud
    • Pull the wiper arm off the stud
    • Open the hood
    • Remove the two 14mm mounting nuts from the passenger side wiper arm
    • Pull the wiper arm off the windshield
  2. step : Removing the Cowl Cover (2:10)
    • Pry off the two cowl corner trim pieces with a trim tool
    • Pry the two push clips out of each side of the cowl with a flat blade screwdriver
    • Release the clips along the front of the cowl
    • Lift the cowl up and out of the engine bay
  3. step : Removing the Wiper Transmission (3:41)
    • Unplug the wiper motor electrical connector
    • Unclip the wiring harness from the lower wiper cowl
    • Remove the four 10mm bolts from the wiper transmission
    • Pull the wiper transmission off the lower wiper cowl
  4. step : Removing the Lower Cowl (5:01)
    • Remove the three 10mm bolts from the lower cowl bracket
    • Remove the bracket from the cowl
    • Remove the nine 10mm bolts from the lower cowl
    • Pull the cowl out of the engine bay
  5. step : Removing the Ignition Coils (6:04)
    • Remove the plastic engine cover
    • Disconnect the wiring harnesses
    • Remove the 10mm bolt from the coil pack
    • Lift the coil pack up and out
  6. step : Installing the Ignition Coils (7:04)
    • Insert the coil into place
    • Tighten the 10mm bolt to the coil
    • Connect the wiring harness
    • Press the engine cover on
  7. step : Installing the Lower Cowl (11:10)
    • Fold over the cowl wind guides
    • Slide the lower cowl into place
    • Insert the nine 10mm bolts into the cowl
    • Raise the cowl wind guides
    • Line up the support bracket on the cowl
    • Insert the three 10mm bolts into the support bracket
  8. step : Installing the Wiper Transmission (10:23)
    • Line up the wiper transmission
    • Insert the wiper transmission pin into the rubber grommet
    • Insert the four 10mm bolts into the wiper transmission
    • Plug in the wiper motor electrical connector
    • Clip the wiring harness to the lower wiper cowl
  9. step : Installing the Cowl Cover (11:56)
    • Slide the cowl under the windshield
    • Push in the clips along the front of the cowl
    • Insert the two push clips into each side of the cowl
    • Clip the corner trim piece onto each side of the cowl
  10. step : Installing the Wiper Arms (12:59)
    • Line up the passenger side wiper arm on the windshield
    • Fasten the two 14mm nuts onto the wiper arm
    • Line up the driver side wiper arm on its stud
    • Fasten the 14mm nut onto the stud
    • Push the cap onto the wiper stud
    • Close the hood

Tools needed for replacement:

    Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 10mm Socket

  • Sockets - SAE

  • 9/16 Inch Spark Plug Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2011-2017 Lexus CT200h Ignition Coil Delphi GN10341
  • 2009-2010 Pontiac Vibe L4 1.8L Ignition Coil Delphi GN10341
  • 2016 Scion iM Ignition Coil Delphi GN10341
  • 2008-2014 Scion xD Ignition Coil Delphi GN10341
  • 2009-2017 Toyota Corolla L4 1.8L Ignition Coil Delphi GN10341
  • 2017 Toyota Corolla iM Ignition Coil Delphi GN10341
  • 2009-2013 Toyota Matrix L4 1.8L Ignition Coil Delphi GN10341
  • 2010-2016 Toyota Prius Ignition Coil Delphi GN10341
  • 2012-2015 Toyota Prius Plug-In Ignition Coil Delphi GN10341
  • 2012-2017 Toyota Prius V Ignition Coil Delphi GN10341

This part replaces:

  • Delphi GN10341
  • Hollander 610-00176
  • OE # 9091902252, 9091902258
  • Hollander 610-50162
Part #: DEECI00038

Ships Same Day for orders placed by 4 P.M. ET

Delphi
Brand #: GN10341

How-to Video:

(14:07 min)