Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Why Delphi?
As an Original Equipment Supplier, Delphi Automotive products from 1A Auto come directly from the source. You wont have to worry about going to the dealership for Original Equipment - these parts are the exact same as the original. Delphi products come with the same quality from the dealership at a lower cost to you.
Item Condition:
New
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
Hey everyone. Sue here from 1A Auto, and today on our '06 BMW 325Ci, we're going to be doing spark plugs. So if you need these parts or any other parts of your car, click on the link below and head on over to 1AAuto.com.
Open the hood on this '06 325Ci. The lever is on the driver's side, left foot. Kick panel right here. It's a long black handle. Just pull on it and the hood pops up. The nice thing about this BMW, the hood latch lever pops right out of the grill area and you just pull up on that and lift the hood open.
The first spot is it's located in the center of the engine department right below the windshield. You've got three little clips here and you just turn them to the side. They pop right up. They're spring loaded. Once those are popped up, you just grab this lid and slide it right out.
Then we're going to lift up the actual seals that goes around this compartment area because we're going to take this out. So you're going to have four t40 bolts. You can see them located up on that firewall. Using a Torx Bit screwdriver, I'm just going to take them all out right across. I'm just going to remove this sheathing so that I can take these wires and make sure that I don't break the tabs. You get the battery cable and the electrical wiring harness.
Now we're going to lift up on this housing and get that out of the way.
So in order to take the engine cover off, we took that out of the way, the cowl up there, and I'm going to take these little covers with a small screwdriver. Just pop them out.
It looks like it's a 10 milliliter. And also you're going to need to take the oil cover off. Set that right there.
10 millimeter socket. I'm going to take these two mounting nuts off this cover. Set those aside. You just grab onto that cover and lift it right up out of the way. Now I'm just going to place the oil cover back on because I just don't want any dirt or accidents to happen and something falling down in that crank case.
To disconnect the ignition coil harness, these are a little levers that pop up. I like to take a flathead screwdriver and I just give myself a little leverage and then you can watch it actually disconnect itself and push the harness out. It's a really nice design. And then you just put your finger right into that hole and give it a twist and pull up and there's your ignition coil.
Now I'm going to take a number one cylinder spark plug out and I'm going to use a spark plug socket that we sell here at 1A Auto on our website, and it is a five-eighths extended, all one piece, and it's great for deep cylinder holes like this, BMW is notorious for. We'll take that right out.
And there is our spark plug. And you can see the crossfire. It's a four-pin crossfire. And this is a magnetic style, so the magnet holds onto it and locks it in. So before I install my new spark plug, because it's a crossfire, four-piece crossfire, there is no gapping, but we do do a visual and make sure that, accidents happen. This could have been dropped at the factory before it went in the box. You want to make sure the prongs are all, look alike visually, the equal distance, and that the ceramic is not cracked, and that includes on this part of ceramic.
Everything checks out good for this plug, so I'm going to install it.
Always install spark plugs by hand first. You don't want to cross thread an aluminum head. That is not a project you wish to tackle. There are torque specs to this. So what I do is I just take my 3/8 and I'll just snug it, crush that washer a little bit and I'll go get my torque specs and torque it down.
So there are two sets of specs for this. If it is a 12-millimeter spark plug, the specs are 14.8 to 19.2 foot-pounds. If it's 14 millimeter, it is 20 to 24 foot-pounds. I'm going with five-eighths, so I'm going with the 14 millimeter and I'm going to set this at 21 foot-pounds.
Now before I install my new coil, you can see a little bit of dry dielectric grease they install the factory. I'm just going to add just a little bit more, nothing too generous.
I'm going to set it up, line it right up, push it down. Feel it physically click in. Make sure it's sealed all the way around, that rubber seal, and line up my connector and then bring this right down and lock it. Now we're going to continue this down and do the same procedure on the next five cylinders.
Now that I've done all my coils and spark plugs, I'm ready to install the engine cover again. So I will remove the oil field cover. Slide this down through. Replace that.
I have the two mounting 10-millimeter nuts, 10 millimeter socket size. We had a plastic cover. I'm just going to really just snug it down. There's no need to crank that down. There we go. And the two covers. Line up the grooves. You'll see the little indent tab here. It's in the front part and then the two longer tabs.
So now I'm going to put that plastic cowl back in. I'm going to just line it right up. Place it right in. Here we go. Get the back screw started. Just pop them into place and take your t30. start them. I recommend starting all of them before you tighten it all the way down.
Okay, so now I'm going to just tighten it down. They're all started. I know it's in the place it's supposed to be.
Now I'm going to put the positive cable back into the housing. I'm going to mount that on that inner beginner clip right on over to the other side. So the positive cable goes down right there and then this harness with the loom will clip into this.
We'll take the under piece and line it up. There's tabs on the back, tab in the front. We'll just line them up and snap it right back up in there.
There you go. To install your cabin filter, you've got a tab right here on the bottom in the middle, I'm sorry, and two tabs on each side, and you'll see that there's a notch right here that tab in the center is going to line up to and the two side tabs. We'll just slide it right in, easily. Line that center tab up, line the side, and then go line up the other side.
Now we're going to install the cover and that just slides right down in the back there. You line up these little tabs, push down and twist.
Now we can install the seal. Just line it, push it down all the way around. I'm going to put this one on before I go over there.
And then we're all set.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Tools used
Hi. I'm Mike from 1AAuto. We've been selling auto parts for over 30 years!
What's up guys, I'm Andy from 1A Auto and today I'm going to be installing some new coil packs in this 2007 Mini Cooper S. If you need these parts or other parts for your vehicle, click the link in the description and head over to 1AAuto.com.
To remove the coil pack connector, you're going to slide this little piece up here. It's a little lock. Slip it up. Sometimes it'll push the connector out. Generally it gets stuck in there, so if you squeeze this tab a little bit, push it up, and you'll slide it out, sometimes, you pull that off. If it doesn't, you can also use a little screwdriver, a little straight screwdriver, and just go back and forth, and eventually pull out the connector.
When the connector's out you can just grab the coil, wiggle it back and forth, pull it out. You're going to do the same for the other three.
Here's our old coil, here's our new coil from 1AAuto.com. As you can see, the shapes are the same, very similar. It’s a similar design, slightly different but still the same. It has the same ratchet lock system for the connector. Get yours at 1AAuto.com and you'll be ready to rock and roll.
To install the coil you just line it up with the hole and slide it down. Make sure this lines up with these two little tabs and push down. Once that's in, you can connect the connector. It's going to line up. It's like a triangle design. Line that up and then you push the ratchet part, lock it in place, and do the same to the other three. You want to make sure they're all the way down. Once you connect them, give it a little push a little further down to make sure it's good. Those are all good.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
I want to disconnect the battery. So, get to the battery in the back. Just use a 10-millimeter socket, remove the negative cable, loosen it up, just slide it off and out of the way. Make sure it doesn't arc out on there. Take these two trim clips out. Just use a trim tool. Try to take the center part out first, and take the push pin out. Do the same on that side. I'm gonna take these two bolts out on this side and the two on the other side as well. On this side, I'll just use a wrench and 13-millimeter and the other side, I can use a socket and a ratchet. And slide this bar out of the way. You want to take this cover off. Twist this right here. This one over here as well. And one on that side. And just grab it, slide it up and just pull the cabin filter up. I'm just going to use a bungee cord. Just go around the wiper arm, just to hold this up.
I'm gonna just keep that out of the way. I'm going to take these four bolts out. Gonna use a T30 socket. And just grab this piece. You should be able to slide it up. Slide this out, and throw all those leaves out. Now, I'm gonna use a 5-millimeter hex bit and take these four bolts out. There's two in the front, two in the back. And just slide this cover off. Just like that. To remove the coil, disconnect the connector. I'm just gonna slide this tab up just like that. And then the connector's going to slide out. It's going to slide straight down. You can grab the coil, just rotate it a little bit back and forth. Try to slide it out as you pull. Now, we're going to pull out the rest of the coils the same way. Now, we can put the coils back in. And reconnect them. Get the connector lined up and push down and lock. Do the same for the others. All right. Now, we can align these wires up. Put this through this retainer there. All right. Slide the wire through here. Put the bolt through. We'll tighten that down. And snug that up. That's good. And slide this thicker wire on top. And slide that right there. Put the nut on. And snug this up. That's good. Put the cover back there and line the cover up right here and lock it in place.
All right. Take the cover, line the cover up. And take the bolts, get all the bolts started and just snug these up. Not too tight. Take this panel, get this lined up. All right. Get that to line up. Get these bolts started. And just snug these down. Now, I'll take the bungee cord away. Put the cabin filter back in. Slide that in position. Actually it goes this way. That looks good. Put the cover on, tighten these down. Turn the locks. And take this bar, line this up. Put these bolts in, two on this side, two on the other side. On this side, I'll just use a ratchet wrench. Tighten these down, snug them up. And take these pushpins, line this up, and lock it down. There we go. Now, we're gonna reconnect the negative battery cable. And tighten up the nut. Just make sure you wiggle it, make sure it's tight. That's good.
Tools used
