Replaces

Hyundai Elantra Tiburon Clutch Master Cylinder - 1ACMC00037

This clutch master cylinder is just what you need to get your clutch functioning properly again. Some symptoms of a failing clutch master are soft / inconsistent pedal feel, clutch disengagement issues, and fluid leakage.

Specifications:

  • 100% New Assembly
    • Not remanufactured
    • No core charge
  • Replaces dealer part number: 41610-2D500, 416102D500
  • No core charge
  • Built to strict quality control standards
  • Bench tested prior to leaving the factory

This clutch master cylinder makes a great replacement and has good cost savings over a dealer unit!

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Checking the Clutch Fluid Level (1:05)
    • If the clutch pedal feels soft, check the level of fluid in the clutch reservoir
    • Make sure the fluid is between the "max" and "min" lines
    • Add fluid if necessary
    • If the reservoir is filled, the clutch master cylinder may be the cause of the problem
  2. step : Disconnecting the Clutch Pedal (1:27)
    • Pull the pun off the clutch connecting rod with needle nose pliers
    • Pull the washer off the clutch connecting rod by hand
    • Slide the connecting rod off its post
  3. step : Removing the Clutch Master Cylinder (2:08)
    • Disconnect the clutch line from the master cylinder with an 11mm wrench
    • Remove the two 12mm nuts from the master cylinder
    • Remove the 10mm bolt from the master cylinder
    • Pull the master cylinder up and out
  4. step : Preparing the New Master Cylinder (4:32)
    • Compare the distance from the mounting flange to the pedal linkage on the new master cylinder to the old
    • Turn the adjusting nut clockwise to increase the length on the new master cylinder or counterclockwise to shorten it, as necessary
    • Have a drain pan ready
    • Loosen the reservoir hose clamp on the old master cylinder with pliers
    • Pull the reservoir and hose off of the old master cylinder
    • Push the reservoir and hose onto the new master cylinder
    • Tighten the hose clamp with pliers
    • Add hydraulic fluid to the reservoir
    • Pump the connecting rod to bench bleed the master cylinder
    • Check the fluid level
    • Add fluid as necessary
  5. step : Installing the New Clutch Master Cylinder (6:34)
    • Push the new master cylinder into place
    • Hang the master cylinder on its studs
    • Attach the clutch line to the master cylinder
    • Fasten the two 12mm nuts onto the master cylinder
    • Insert the 10mm bolt for the fluid reservoir
  6. step : Reconnecting the Clutch Pedal (7:55)
    • Press the connector rod onto the clutch pedal
    • Put the washer onto the connecting rod
    • Clip the pin onto the clutch connecting rod
  7. step : Bleeding the Clutch (8:25)
    • Pry the plastic cap off the bleeder screw with a flat blade screwdriver
    • Attach a hose to the bleeder valve, with something to catch the fluid
    • Attach a 10mm wrench to the bleeder
    • Enlist the help of an assistant
    • Instruct the assistant to pump the clutch pedal and then hold it
    • Loosen the bleeder valve
    • Tighten the bleeder valve
    • Repeat this process until fluid rather than air comes out of the bleeder valve
    • Check that the reservoir is full to the proper level
    • Add fluid to the reservoir as necessary
    • The clutch pedal should feel firm

Tools needed for replacement:

    General Tools

  • Drain Pan
  • Assistant

  • Materials, Fluids, and Supplies

  • Cloth Rags
  • Brake Fluid

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 12mm Socket

  • Wrenches - Metric

  • 11mm Wrench
  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(11:14 min)

Tools List:

    General Tools

  • Drain Pan
  • Assistant

  • Materials, Fluids, and Supplies

  • Cloth Rags
  • Brake Fluid

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 12mm Socket

  • Wrenches - Metric

  • 11mm Wrench
  • 10mm Wrench



This part replaces:

  • OE # 416102D500
  • Hollander 417-50325
  • Dorman CM640111

Vehicle Fit

  • 2005-2006 Hyundai Elantra Clutch Master Cylinder
  • 2005-2009 Hyundai Tiburon Clutch Master Cylinder L4 2.0L
Only 1 left in stock
Part #: 1ACMC00037

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More