Menu

1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles

How to Replace Rear Window Glass 06-11 Toyota Camry

Share on:
  1. step : Removing the Door Panel (0:26)
    • Pry the trim panel out of the door handle with a trim tool
    • Remove the Phillips screw inside the door handle
    • Pry the trim panel off the door pull with a trim tool
    • Remove the two Phillips screws inside the door pull
    • Pop out the door panel clips
    • Lift the door panel up and off the door
    • Pull the door handle out of the back of the door panel
    • Disconnect the window switch electrical harness
    • Remove any push clips stuck in the door with a trim tool
    • Slide the push clips into the door panel
  2. step : Removing the Interior Door Handle (2:38)
    • Push the cables up and out
  3. step : Removing the Window Switch (4:15)
    • Peel off the weatherstripping
    • Slide the cables out of the weatherstripping
    • Press on the weatherstripping
    • Pry out the window switch with a door trim removal tool
    • Plug in the window switch
    • Lower the window
    • Turn the ignition off
  4. step : Removing the Window (4:52)
    • Disconnect the window switch
    • Disconnect the window motor
    • Pull out the window run channel
    • Remove the two 10mm bolts from the window track
    • Remove the Phillips screw from the channel
    • Remove the run channel/window track
    • Remove the rubber from the channel
    • Raise the window by hand
  5. step : Reinstalling the Window (6:51)
    • Insert one of the bolts into the window regulator
    • Push the regulator into the door
    • Hang the regulator by its bolt
    • Insert the four 10mm bolts into the regulator
    • Lower the window onto the regulator
    • Insert the window channel
    • Tighten the 10mm bolts to the channel
    • Tighten the Phillips screw to the channel
    • Press on the window channel weatherstripping
  6. step : Reinstalling the Interior Door Handle (13:34)
    • Connect the white latch to the lock
    • Connect the green latch to the door
  7. step : Installing the Door Panel (14:20)
    • Pop the door handle into the door panel
    • Connect the window switch electrical harness
    • Line up the door panel with the door
    • Push in the door panel clips
    • Insert the Phillips screw into the door handle
    • Clip on the door handle trim
    • Insert the two Phillips screws into the door pull
    • Clip on the door pull trim piece

Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!

This video shows you how to remove the rear glass. Ours is not broken. If yours has been broken, clean up all the broken glass and then follow the steps for installing it.

I’m working on the rear passenger door. I’m going to remove it. We're going to use these plastic trim tools. You can get these from 1AAuto.com. Pry out this plastic piece that's behind here. Pop the trim tool in here. I’m just going to hold open the door handle. That pops it right out. Put that aside. Remove the screw with a Phillips head screwdriver.

Use our plastic trim tool again. Slide it under here. Pop this handle cover off. Just kind of work it underneath. Put that aside. There's two screws, Phillips head. Remove those. If that screw stays in there, that's fine; we can grab it after we pop the door off. With the three screws removed, we can pop the door off the clips. There's a bit of a lip here, just on the inside of the door. Pull behind it, and I can reach underneath. You just want to reach around the edge of the door, and we pick the door panel up and up from the door. There's the screw that fell out.

Pull the door handle and lock mechanism out, just pops it out, and it'll sit there. Unplug the harness for the window switch. Push in on the lock. Put the door panel aside.

These push clips, they're not damaged; they just popped out. One stuck in the door. I'll use a trim tool to pop that one out. This one went down here and came out, so I'm just going to put it back in. It just slides back into place. It can be reused. I've just got to get that one out of the door.

Going to disconnect the handle that opens the door. Also has the door lock on here. Just going to push the cable up and out and slide that little lead weight. Pop it right out. Same for the other one. Take note that the white was on the top, the green was on the bottom so when you go to put it back together, you don't reverse them.

We need to pull this vapor barrier off the door. It's got butyl tape around it that's sealing it. I can be reused. This is where you're going to want to wear gloves because this stuff is very, very sticky and it kind of gets everywhere but you basically just carefully peel this back. You can have a razor blade with you with you, and you can just kind of cut it. It helps on a warmer day to do this. If it peels off, don't worry about it because this stuff is incredibly sticky and we should be able to reuse this piece without much issue. I'm just going to carefully cut that. Try not to stretch the pink plastic too much.

As you're moving along, so this harness is kind of in this opening here. I'm going to feed the harness back through, and I'm just going to keep peeling it. I'm going to feed these wires out, actually these are the cables. They kind of sit there. I'm going to put this aside, obviously sticky side up so that we can reuse it.

To remove this window, we're going to take a plastic prying tool. You're going to pry out and try to feed this up and it pops right out of place. We have the ignition turned on in the car, we're going to plug in the window switch that I pulled out of the door panel. Now be careful that you don't have your hand in here or anything when you put this down. You could pinch your fingers. So we're going to put the window glass all the way down.

You need to slide this window glass off of this track. So this run channel's going to have to be removed. I'm going to go turn the ignition off so that I can't hit the window switch by accident and pinch my fingers. We're going to disconnect the switch so the door window can't move anymore. I'm also going to unplug the window motor, which is right here.

Just use a small flat-bladed screwdriver to push up on the lock and pop it out. This way, the motor can't move at all because I'll have my fingers in there. I don't want them to get caught. We're going to pull the window run channel out of here. Just kind of work it out with my fingers. Just pull it down. Put that aside.

We're going to loosen up the 10 millimeter bolt here that's holding the top of the run channel. Loosen up the bottom one. Put those bolts aside. So this rubber just pulled out of here. At the very top, we're going to pull back this rubber. There's a screw holding in the run channel. Using a Phillips-head screwdriver, we're going to remove it. Put that screw aside. So now that these bolts are removed, we're going to pull some more of this rubber run channel back. I can slide the metal piece out and just kind of feed it out of the door opening. We'll just put this aside and pull the rubber run channel out and just lay it on the outside of the door. We can go inside the door cavity here.

This glass has to slide to the outside to slide off of this track. So support it with my hand so it doesn't fall off and also kind of lift it up. You might have to angle it a bit, so it's going to come loose and you're going to very carefully pull it out of the door opening to put this aside because you don't want to break it. So your glass has a curve to it. It's only going to go in one way. Kind of matches the curvature of the door. So I'm just going to slide it in very carefully. Don't force it. It should just slide in freely. I'm going to reach down, guide it in with my hand. Now that I'm down here, I want to get it back on this little pivot point.

Pivot point's kinda got this kind of rectangle shape. So it might not fit. If it's this way, or maybe it's square. So it's square shaped. It should fit either direction as long as you have it lined up right. You're going to get it in place. It's just going to be loose. Going to put it sort of there. You're going to set it into the run channel over here so it's not bouncing around for now.

I'm going to wipe the grease off my fingers to install that run channel. This is our run channel. This part goes against the glass. This rubber is going to go in it eventually, but we need to feed this into the door panel so it can sit like this. I'll just carefully work it in here. I did hit the glass, but I'm going to catch it and put it back over. Hold that there in my hand. I'll get this flipped and turned into position. I want to take the run channel. I'm going to slide it down into position. I'm going to push it into the metal run channel.

Now I'm going to mess with the glass and move it around until I can get the glass settled into this channel. I should pop this out a little bit and bring this up. See it up in the top of the door frame? At the same time, I'm also trying to work the window glass into the channel. I've got to use both hands to maneuver it. I've got that in place, and I'm going to push well, I'm going to get this into place, basically where I want it. I'm going to put one of the bolts in there to just hold it in place so it doesn't move around. I'm not going to fully tighten it though. I just don't want it to fall out.

I've got the bottom one caught. I've got the bottom bolt in. I've got everything loose. The glass is in the rubber in the channel. I'll push this up into place. I had to fiddle with this rubber a little bit, make sure it fits right. That all into place, a screw in there, feed our rubber into here.

The rubber actually needs to go down more. I can slide it on the glass a little bit. It's seated all in here, and this side, that's pushed under there. I like where those are sitting. I can actually see there's actually little wear marks where the bolts were, so I'm going to line this one back up where it was. Just tighten it down. If it feels tight, I'll stop. I'm going to turn the ignition on again.

I'm going to plug our window motor in, and plug our window switch in. I'm just going to test it, make sure it goes up and down.

We got our original vapor barrier here. Still has a lot of the butyl tape left on there. If you need to get more butyl tape, it's pretty easy to get and you can just put some more on there.

First, I'm going to feed the cables through. Just got to get them through. Just kind of let it hang on the cables. I'm going to feed the harness up and through. That's everything, so I'm just going to kind of line it up roughly where it was before and just push it back into place. Don't worry too much about any wrinkles. Just push it down and it'll seal. In this car, the white cable went on top, and the green one went on the bottom.

You can kind of tell by the length of the cable which one fits better, because they will both fit in both spots, but you'll end up crossing them so this will want to open the door and this will want to lock the doors, which you don't want that. You want this to open the door, and you want this to lock the door. White one's going to go in the top, but that little lead weight and the end of the cable in like that. Put it over. Put the green one in just like that. That works the door.

Now we're going to need to install our door panel. Take our door panel, make sure all of our clips are okay. Take this, it's going to slide in like that. There's two pins in the top and the bottom that match this. It pops into place. Don't forget to plug in your window switch. Nothing like putting this together and then having to take it back off to plug it back in. There's a groove in here with some clips. They're going to snap into place in here so I'm going to start with the door panel kind of on the high end. It might be easier with the window down but you can do it with the window up. I'm just going to snap it down into place. Then we're going to go down, push all the clips in. Start with the small screw that's behind this. Put the plastic cover back in. You'll start by pushing that clip in first, then it'll snap in the back ones, so open the door handle, snap that into place. We have to do the other two screws in the door handle. Just kind of goes straight on.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Tools needed for replacement:

    General Tools

  • Razor Blade / Gasket Scraper

  • Materials, Fluids, and Supplies

  • Gloves

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Star Drivers & Sockets

  • T25 Driver


Search Videos
Go To Top


Same Day Shipping

Orders ship same day when ordered by 2pm ET. Need your part faster? Choose expedited shipping at checkout.


Guaranteed To Fit

Providing you the highest quality, direct fit replacement auto parts enforced to the strictest product standards.


USA Customer Support

Exceeding customers' expectations every day, our team of passionate auto enthusiasts are here to help.


Instructional Video Library

Thousands of how-to auto repair videos specific to year, make and model guide you step-by-step through your repair.

Loading...