1A Auto Video Library
Our how-to videos have helped repair over 100 million vehicles.

How to Replace Door Panel 95-01 Ford Explorer

Share on:

How to Replace Door Panel 95-01 Ford Explorer

Created on: 2021-01-16

In this video, 1A Auto will teach you how to remove the door panel on your 95-01 Ford Explorer. This will give you access to the window and lock mechanisms

  1. step 1 :Removing the Door Panel
    • Pry out the door handle bezel
    • Remove the two Phillips screws under the door pull.
    • Pry out the upper switch.
    • Disconnect the harness.
    • Using a putty knife pry out the clips around the door panel.
    • Lift the door panel up and off.
    • Press down the teeth and slide the switch panel through.
  2. step 2 :Replacing the Door Panel
    • Line up the grooves on the switch panel with the pins on the door panel and slide it into place and lock it.
    • Put the panel up into place on the window groove and push the clips back into the door.
    • Reconnect the upper switch and replace it.
    • Replace the door handle bezel
    • Replace the two Phillips screws.

Tools needed for replacement

  • General Tools

    Putty Knife

  • Screwdrivers & Related

    Flat Blade Screwdriver

    Phillips Head Screwdriver

Installation Video
Watch video

Brought to you by, your source for quality replacement parts and the best service on the internet.

Hi. I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from The rights parts installed correctly, that's going to save you time and money. Thank you and enjoy the video.

In this video, we show you how to remove and put the door panel back on this 98 Explorer, front driver side. Really, tools you'll need are flat blade screwdriver, a Philips screwdriver and a putty knife or a door panel clip removal tool.

Okay, removing the door panel in one of these Explorers, you'll need three tools: flat blade screwdriver, Philips screwdriver, a putty knife and if you worry about your paint you might want a rag as well. You want to start. Use your flat blade screwdriver, carefully prying back here, you could see mine is already broken. You want to be careful not to break it right there, it's a weak spot. Even if you do break it, you'll put it back together so it doesn't you might notice it. Pull that bezel apart and off. Two Philips screws under here, remove those Philip screws. Back with your screwdriver and if you want, use your rag by the top and the bottom, pull it out. Use a screwdriver. There's side here that has a tooth holding the harness. Just work that screwdriver there a little bit and disconnect it. Now, around the perimeter of the door panel, there are some pins that hold it. What you want to do, if you worry about paint, put the putty knife, wrap the towel around it, work it in, slide that down till you come to the stop and that's usually a pin then pull. I'm through. This truck has been apart a few times so it comes out pretty easy. Once you have those pins released then you want to lift up on the panel, from this groove here.

Behind here, what you want to do is, this is held in, you basically want to - there's two teeth on there and then one back here. You press those down to release them and then it slides out. On this one, press is down and then that whole assembly slides right out. Work that screw and there's the door panel off.

I'm reinstalling the door panels. Here's all the pins. It's pretty easy. What you want to do is first, take your switch panel on your switch panel, there is grooves, here and then also on the front. They go right over this pin here and this pin here. You basically just slide it right in and walk it into place. Make sure your mirror harness comes up and through and now, you want to get your grommet up and over the door lock here. You want to make sure that the top of the panel goes right down into the screw, you want to push it towards the window. Work with the top of the panel into that groove. Work from the back forward.

Now, reach in behind and feel for your pins and make sure they go in to their respective holes in the door. Roll each one of those in, push that all on. You put your mirror switch, put that back in and shoot down. The grommet around the door handle. Back in. Two screws above the door handle here. Nice and firm and they do angle up as they go in.

We hope this helps you out. Brought to you by, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free, 888-844-3393. We're the company that's here for you on the internet and in person.

Tools needed for replacement:

    General Tools

  • Putty Knife

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

SOLVED Low speed ABS activation Chevy Trucks

SOLVED Low speed ABS activation Chevy Trucks

If the ABS pump engages and the brake pedal presses further than usual and pumps soft and hard, engaging the antilock brakes, this video has a solution

Search Videos
Go To Top

Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.