How to Change Oil and Filter 18T 2004 Volkswagen Jetta and Golf
Created on: 2014-03-28
How to drain, refill, or replace old, dirty or clogged oil and oil filter on 04 Volkswagen Jetta or Golf
-
step 1 :Raining the Oil
- Raise and secure the vehicle
- Have a drain pan ready
- Remove the drain plug from the oil pan with an 8mm Allen bit and ratchet
- Allow the oil to drain
- Insert the drain plug into the oil pan
-
step 2 :Removing the Splash Shield
- Remove the T25 Torx bolts from the splash shield
- Pull down the splash shield
-
step 3 :Removing the Oil Filter
- Have a drain pan ready
- Loosen the oil filter with an oil filter wrench
- Twist off the oil filter by hand
- Allow the oil to drain
- Remove the oil filter
- Clean the oil filter mounting area
-
step 4 :Installing the Oil Filter
- Apply oil to the oil filter gasket
- Twist on the oil filter by hand until the gasket is seated
- Turn the oil filter another 3/4 turn
-
step 5 :Installing the Splash Shield
- Put the splash shield into place
- Insert the T25 bolts into the splash shield
-
step 6 :Filling the Oil
- Lower the vehicle to the ground
- Twist off the oil cap
- Add oil using a funnel
- Twist on the oil cap
- Run the engine briefly
- Check the oil level
- Add oil as necessary
Tools needed
-
Funnel
Oil Filter Wrench
8mm Allen Wrench
Jack Stands
Ratchet
Cloth Rags
Floor Jack
T25 Torx Driver
Engine Oil
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to do an oil change on this 2004 Volkswagon Jetta with the 1.8T engine. The items you'll need for this is an 8mm Allen bit and ratchet, T15 Torx bit, oil filter wrench, oil, oil filter, drip pan and jack and jack stands.
Your oil pan is located right here. On the back of it there's this drain plug. Using an 8 mm Allen bit, just loosen up and remove that drain plug. Make sure you have your drip pan underneath and just let the oil drain out. Once it stops draining replace your drain plug and tighten it up.
Next you want to remove this panel by removing this series of T25 bolts. You can see that most of ours are missing so Don's just going to remove this one T25 bolt and then cut these wire ties and then just pull that panel free.
Now you can access your oil filter. Using an oil filter wrench, just loosen up the filter and put your drip pan underneath and twist out the oil filter by hand. Just let the oil slowly drain out, twist it out, let it drain for a second, twist it out more and then you can just remove it the rest of the way. Wipe down the area where the oil filter was.
Coat the rubber gasket of your new oil filter with some fresh oil and then put your oil filter up in place, spin it on until the gasket hits and it stops spinning, and then turn it another two-thirds to three-quarters turn to tighten it.
Just feed this panel back up and clip it on to that other panel. Make sure all the holes line up and then replace your T25 bolts or in our case our T25 bolt.
Now lower your vehicle and remove your oil cap and then using a funnel replace the oil in your engine. When you're done replace your cap, start the vehicle and let it run for a little bit. Then just check the oil level. If it needs more oil, add some more. Just make sure it's at the proper level and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
How To Change Oil 2002-13 Jeep Liberty
Watch this video to learn how to change the oil in your 02-13 Jeep Liberty.
