Replaces
Honda Drum Brake Hardware Kit - 1ABRX00013
1ABRX00013Specifications:
- Will service both LH (Driver Side) & RH (Passenger Side) Rear
- Kit includes:
- 4 Springs
- 6 Retainers
- 4 Pins
- Direct replacements
- Built to strict quality control standards
Lifetime Warranty
This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.
-
step : Removing the Wheel (0:54)
- Loosen the lug nuts with the vehicle on the ground
- Raise the vehicle with a floor jack
- Secure the vehicle on jack stands
- Remove the lug nuts
- Pull of the wheel
-
step : Removing the Brakes (1:20)
- Pull off the brake drum
- Remove the springs with locking needle-nose pliers
- Push the piston in by hand and lock the rubber in place
- Remove the tabs with the pliers
- Pull the brake shoes apart
- Remove the front brake shoe
- Remove the separator bar
- Pull the rear brake shoe off the emergency brake cable
- Remove the emergency brake lever from the rear brake shoe
-
step : Installing the Brakes (3:59)
- Connect the emergency brake lever to the new rear brake shoe
- Attach the rear brake shoe to the emergency brake cable
- Apply white grease to the contact areas on the backing plate
- Put the rear shoe into place
- Insert the tab
- Make sure the separator bar adjusts freely
- Insert the separator bar
- Attach the front shoe to the rear shoe via the spring
- Put the front shoe into place
- Insert the tab
- Reattach the springs with the pliers
- Slide the brake drum on
-
step : Reattaching the Wheel (7:37)
- Slide the wheel into place
- Put the hub cap on
- Start the lug nuts by hand
- Tighten the lug nuts preliminarily
- Lower the vehicle to the ground
- Tighten the lug nuts to between 100 foot-pounds in a crossing or star pattern
- Reattach the center cap
-
step : Testing the Brakes (8:08)
- Pump your brakes repeatedly until they feel firm
- Test your brakes at 5 miles per hour and then 10 miles per hour
- Road test the vehicle
Tools needed for replacement:
- Jack Stands
- Floor Jack
- White Grease
- Lug Wrench
- Vise Grip Pliers
- Torque Wrench
- A Piece of Pipe (for leverage)
- Ratchet
- 1/2 Inch Breaker Bar
- 19mm Socket
General Tools
Materials, Fluids, and Supplies
Pliers, Cutters & misc Wrenches
Ratchets & Related
Sockets - Metric
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Vehicle Fit
- 1988-1991 Honda Civic Wagon Rear Drum Brake Hardware Kit
- 1992-1995 Honda Civic Sedan Rear Drum Brake Hardware Kit for Models with Automatic Transmission
- 1993-1995 Honda Civic DX Coupe Rear Drum Brake Hardware Kit for Models with Automatic Transmission
- 1993-1995 Honda Civic EX Coupe Rear Drum Brake Hardware Kit
- 1996-2005 Honda Civic Rear Drum Brake Hardware Kit
- 2006-2009 Honda Civic Rear Drum Brake Hardware Kit excluding GX Models
- 1988-1989 Honda Civic Wagovan Rear Drum Brake Hardware Kit
- 2007-2010 Honda FIT Rear Drum Brake Hardware Kit
- 2010 Honda Insight Rear Drum Brake Hardware Kit
This part replaces:
- OE # 140751465
- Dorman HW17307