Replaces

Honda CR-V Strut & Spring Assembly TRQ SCA57643 - 1ASTS01086

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

To ensure the vehicle performs safely and as designed, we recommend replacing shocks & struts in pairs. If the damping rates are significantly different from side to side (like using different brand parts or mixing old with new) the vehicle body and wheel movement variations could cause handling irregularities. We also recommend performing an alignment after replacement. This will ensure proper tracking and protect your vehicle's tires from premature wear.

Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Item Condition: New

California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:48)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Front Strut and Spring Assembly (1:28)
    • Place a 17mm wrench on the upper sway bar link nut
    • Grab the sway bar link joint with a 6mm allen wrench and socket
    • Loosen the 17mm nut with a socket and ratchet
    • Remove the sway bar link from the strut
    • Pry the ABS sensor wire out of its retainer in the strut
    • Remove the 12mm bolt on the brake line brace
    • Remove the two 22mm lower strut bolts with a 19mm wrench and 22mm socket and breaker bar
    • Tap the bolts out with a hammer and punch if needed
    • Peel back some weatherstripping from the cowl panel
    • Undo the cover on the cowl panel
    • Loosen the 14mm nuts on top of the strut
    • Remove the nuts with a magnet
    • Remove the strut
  3. step : Installing the Front Strut and Spring Assembly (8:52)
    • Reinstall the strut into the vehicle
    • Hand-tighten the top nut
    • Torque the upper nuts to 33 foot-pounds
    • Replace the cowl cover
    • Replace the weatherstrip
    • Insert the steering knuckle into the strut
    • Tighten the lower bolts with a 19mm socket and ratchet
    • Torque the bolts to 116 foot-pounds
    • Reinstall the brake hose into the retainer
    • Tighten the 12mm bolt to the retainer
    • Pop the ABS sensor into the bracket
    • Reinstall the sway bar link into the strut
    • Grab the sway bar link joint with locking pliers and a 6mm allen wrench and socket
    • Tighten the 17mm nut with a socket and ratchet
  4. step : Reattaching the Wheel (14:16)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Torque the lug nuts in a crossing or star pattern to 80 foot-pounds

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Magnet - Extendable
  • Center Punch
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 17mm Socket
  • 19mm Socket
  • 22mm Socket

  • Specialty Tools

  • Trim Tool Set

  • Wrenches - Metric

  • 17mm Wrench
  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2007-2011Honda CR-V Honda CR-V Front Strut & Spring Assembly Driver Side TRQ SCA57643
2012-2014Honda CR-V Honda CR-V Front Strut & Spring Assembly Driver Side (excluding Touring Models) TRQ SCA57643

This part replaces:

  • Hollander 527-50268L
  • Hollander 527-60693L
  • Monroe 272492
  • TRQ SCA57643
Part #: 1ASTS01086


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: SCA57643

How-to Video:

(15:13 min)